最新刊期
      卷 ， 期 2 ， 1994
      • IIuo Jingping, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.002
        摘要：Comapared with the gencrating mothed,the fall formate method is with many merits in cutting internal spiral level spiral level gears, In this paper, the tooth surrace equations and calculative procedure of contact points are given of the internal spiral level gears cut by the full formate method, the second-order analysis for mulae at any contact pount and the third-order analysis fromulac at reference point are devcloped, the analysis results are also discussed.  
        关键词：全成形法;弧齿锯齿轮;接触分析   
        2
        |
        131
        |
        1
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683457 false
        更新时间：2025-04-03

      • The parameter and Performance Analysis of Planetary Cone CVT

        Dong Zhifeng, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.003
        摘要：This paper deals with the mechanisms and performance of planetary Cone CVT, discusses the relations of the geometrical structure parameters, presents the formulas of transmission ratio and contact load which are expressed with geometrical structure parameters, and analyse the effects of modifying these parameters on contact load and stress.  
        关键词：无级变速传动;几何参数;传动比;力分析   
        2
        |
        104
        |
        1
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682722 false
        更新时间：2025-04-03

      • Shell-Lifter Performance Reliability Analysis

        Sun Youchao et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.004
        摘要：In this thesis, the author analysed the performance reliability of the shell-lifter, cstablished the simulation model of the performance reliability analysis of the shell-lifter and gave a kind of analysis method for the performance reliability by the example.In addition, the author indicatied the importance of the performance reliability.  
        关键词：提弹机构;模型;性能可靠性;系统仿真   
        2
        |
        70
        |
        1
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683531 false
        更新时间：2025-04-03

      • Study of Load Distribution Along the Contact Lines of Cylindrical Gears

        Li Janfeng, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.005
        摘要：The new method of normal direction stiflness matrix of contact lines of gear tecth, which analyses gear tooth stiffness and distribution along contact lines is presented. The The relation between nodal forec of contact lines and normal deformation has been established. toad distribution along the contact lines,load sharing among contact tecth and instantaneousmesh stiffness are analyzed by adding deflection concord condition and force cquilibrium condition. A special software calculating load distribution is developed.Calculating examples and load distribution curves in consideration of multi-tooth contact, stiffness and boundary effect are given out . The method gives up plane assumption and is suitable for practical load distribution, so the results have high accuracy and reliability.  
        关键词：齿轮;瞬时刚度;载荷分布;有限元   
        2
        |
        354
        |
        25
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682512 false
        更新时间：2025-04-03

      • On Surface Durability（pitting） of Through IIardened Gears

        Meng Jinxian, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.006
        摘要：The main proccsscs and rcsults of test on surface durability （pitting） of 40Cr and 35CrMo through hardened gcars are presented. The distribution paremcters of fort data are cstimatcd and inspected with computer. The present work gives two curves of R-S-N and provides the contact endurance limits to predict the gcars life.  
        关键词：齿轮;接触疲劳;强度试验   
        2
        |
        242
        |
        5
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683169 false
        更新时间：2025-04-03

      • The Problem or Creep in Belt Drives and Band Brakes

        Zhu Cogjian
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.007
        摘要：The problem of the Creep in belt drives and band brakes is considered in the paper.The limited position of creep and determined method of creep direction are pointed out.The formulas of the creep sizc,average velosity of the creep, maximm velosity of the creep and so on is deriven,The efficiency of the belt drive and the ratio transmission of the belt drive are analyzed.  
        关键词：弹性滑动;带传动;带式制动器;摩擦力;弹性滑动系数   
        2
        |
        190
        |
        16
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683340 false
        更新时间：2025-04-03
      • Zhang Youchen
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.008
        摘要：This paper discussed the influence of gcar prcssure anglc on mcan flash temperature of tooth surface based on the integral tegral temperature mcthod.  
        关键词：齿轮;胶合;压力角;平均温升   
        2
        |
        88
        |
        7
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682947 false
        更新时间：2025-04-03

      • 圆柱斜齿轮螺旋角的精确测量

        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.009
        摘要：圆柱斜齿轮螺旋角的精确测量荆门市沙洋机床厂潘泽文（荆门市４３４５６０）在机械设备的维修中，经常遇到圆柱斜齿轮损坏而需要更换的情况，这就必须确定其螺旋角，螺旋角的精确与否直接影响装配和使用，尤其对齿部较宽的斜齿轮和精密机械上的斜齿轮，其影响更人。根据在...  
          
        2
        |
        41
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683297 false
        更新时间：2025-04-03

      • Study on IIobbing Experiment of of through hardened Gears

        Chen Yuan, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.010
        摘要：The results of hobbing right-angle experiment for a group of through hardened involute gears （HBS 330-340） and for several groups of comparing experiments are described in this paper.Some factors which influenced the hobbing of fects-gcometric accuracy and roughness of the tooth surface-are analyzed. At the same time, suitable finish hobbing standards, methods of cortrolling quality and economical manufacturing accuracy of the gears are al so put forward.  
        关键词：中硬齿轮;正交试验;切削规范   
        2
        |
        23
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682863 false
        更新时间：2025-04-03

      • Experiment of Shaving and Regression Analysis of Tooth Error

        Yao Wenxi
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.011
        摘要：In this paper, the influence degrces of three primary factors on tooth errors have been analysed by measuring the tooth error curvers which is obtained by shaving.Through regression analysis, a formulac of bitting profile crror is given for refcrence.  
        关键词：剃齿;齿形误差;回归分析   
        4
        |
        64
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682443 false
        更新时间：2025-04-03

      • Optimum Approximate Circles for a Kind of Segmental Curve

        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.012
        摘要：花键滚刀齿形与摆线、渐开线等曲线有某些共同点。本文对这类曲线段圆弧拟合误差随国心位置的变化规律进行了研究，证明使总误差取最小值的圆心位置为两条辅助曲线的交点，并给出了简单可靠的计算方法，对这类齿形的代用圆弧计算具有一定的意义。  
        关键词：一类曲线段;圆弧;误差;圆心位置   
        2
        |
        34
        |
        2
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88682379 false
        更新时间：2025-04-03
      • Yang Tienan, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.013
        摘要：The paper analyses the dynamic property of planetary decelerator which will be used in the vertical lathe. The problem of cxciting force is mainly studicd in the planctary decelerator system. Through analsing and calculating the mcsh assemble crrors and mesh stiffness,the equations deseribing the exciling force is got In the equations the frequencies frequencies making up the exciting force can be seen clearly.  
        关键词：行星变速器;激振力;啮合误差;啮合刚度   
        3
        |
        91
        |
        5
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683670 false
        更新时间：2025-04-03
      • Chen shuxun
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.014
        摘要：In thos paper, the question of envelope of single parameter curved surface family is changed into the question of the calculation primary function quite ingeniously. And the calculation method conducted from it is very vigorous in methematical concept, its procedures is simple and direct, it is practical for application to engincering, and so it is casy for practical workers tograsp.  
          
        2
        |
        47
        |
        1
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683604 false
        更新时间：2025-04-03

      • Making and Theoretical Working Error of Spherical Hob

        Cui Yunqi, et al.
        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.015
        摘要：The liviter introduces a method of designing the spherical hob. New concept on thooretical working error of generating gcar for the hob and calculating mothod of its working theoretical crror are prosented. Various factors influencing theoretical crror are analysed.  
        关键词：球面螺旋面;圆周铲齿;产形齿轮;理论误差;投影光线   
        2
        |
        59
        |
        7
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683015 false
        更新时间：2025-04-03

      • 简单行星轮系效率的一个计算公式

        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.016
        摘要：简单行星轮系效率的一个计算公式黑龙江矿业学院贾宝贤行星轮系多用丁传递动力，其效率的计算是个十分重要的问题。日前ｃ有不少计算效率的方法和公式，它们不是公式太长就是推导太繁，应用起来不够方便。本文给出了用速比法得到的一个统一公式，并介绍了应用这一公式计算...  
          
        3
        |
        105
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683638 false
        更新时间：2025-04-03

      • 超万级齿轮变速箱设计

        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.017
        摘要：超万级齿轮变速箱设计杭州电子工业学院王德奎前言在纺织机械中为满足纺纱细度、捻度和织物纬密等工艺调节的需要，其电子电气绕纸设备都需设有变速机构。但是，这类工艺中某些参数的变化范围大，所需速度档数多，各档要求连续且不重档，有时两档问的速度差很小，变速精度...  
          
        2
        |
        93
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683247 false
        更新时间：2025-04-03

      • AHRX机械自控无级变速器

        Issue 2, (1994) DOI: 10.16578/j.issn.1004.2539.1994.02.018
        摘要：ＡＨＲＸ机械自控无级变速器宁波市浙东变速器厂周鸣杰，许顺康前言ＡＨＲＸ机械自控无级变速器是一种新颖的较理想的无级变速器。它能根据转矩变化而自行调节转速。本厂在渐江人学机械系指导下，在１９９０年试制出样机。经测试，自控变速是灵敏的，转速、滑差、温升都达...  
          
        2
        |
        26
        |
        0
        <HTML>
        <Meta-XML>
        <引用本文> <批量引用> 88683393 false
        更新时间：2025-04-03
      0