
浏览全部资源
扫码关注微信
1.江苏理工学院 机械工程学院,常州 213001
2.重庆大学 高端装备机械传动全国重点实验室,重庆 400044
3.智能制造龙城实验室,常州 213164
吴兆健,男,2001年生,江苏连云港人,硕士研究生;主要研究方向为精密减速器传动系统设计、轻量化设计与分析;jsutwzj@163.com。
韩振华,男,1986年生,山东菏泽人,博士,副教授;主要研究方向为机电精密传动系统设计与驱动方法、机电传动系统创新设计等;han_jsut@jsut.edu.cn。
收稿:2026-06-25,
修回:2026-08-18,
录用:2026-08-19,
网络首发:2026-11-04,
移动端阅览
吴兆健,韩振华,徐浪,等.考虑多孔结构的RV减速器摆线针轮啮合特性分析[J].机械传动,XXXX,XX(XX):1-13.
Wu Zhaojian,Han Zhenhua,Xu Lang,et al.Meshing characteristic analysis of cycloidal-pin gear pair for RV reducer considering multi-hole structure[J].Journal of Mechanical Transmission,XXXX,XX(XX):1-13.
目的
2
针对摆线轮多孔结构引起的刚度分布不均、轮齿受载变形复杂与运动传递机制难以表征的难题,提出一种考虑多孔结构的摆线针轮有限元承载接触建模与分析方法,并结合正交试验研究扇形孔结构参数对啮合特性的影响规律。
方法
2
考虑摆线轮中心孔、曲柄轴承孔与扇形孔等关键多孔结构特征,根据RV减速器运动学关系与轮齿接触约束,建立摆线针轮少齿差行星传动有限元承载接触模型。分析啮合力、接触应力、同时啮合齿数与传动误差等啮合特性仿真结果,阐明摆线轮多孔结构参数对啮合特性的影响机制;以扇形孔结构参数(上底圆半径、两腰夹角、下底圆半径与倒角半径)为试验因素,制定四因素五水平的正交试验方案,采用极差分析法研究扇形孔结构参数对齿面最大接触应力与传动误差幅值的影响规律。
结果
2
结果表明,相较于传统简化实体模型,多孔摆线轮模型有限元结果的啮合力和接触应力峰值分别增大35%和13%;同时啮合齿数由简化实体模型的7对变为5~9对波动;多孔摆线轮模型传动误差幅值(9.86″)较简化实体模型显著增大(26.6倍);传动误差曲线在保持基本啮合周期特征外,呈现出更明显的附加波动。极差分析表明,上底圆半径对齿面最大接触应力影响最为显著,取其较小值可降低齿面接触应力峰值;两腰夹角是影响传动误差幅值的主要因素,减小两腰夹角有利于改善传动精度;下底圆半径的影响相对较弱;适当增大倒角半径有利于降低传动误差幅值。研究结果可为高性能RV减速器摆线针轮的正向设计与结构优化提供依据。
Objective
2
The multi-hole structure of cycloidal gears causes non-uniform stiffness distribution
complex loaded deformation of gear teeth
and difficulty in characterizing the motion transmission mechanism. To address these problems
a finite element load-bearing contact modeling and analysis method for cycloidal-pin gear pairs considering the multi-hole structure was proposed
and orthogonal tests were conducted to study the effects of sector-shaped hole structural parameters on meshing characteristics.
Methods
2
The key multi-hole structural features of the cycloidal gear
including the central hole
crank bearing holes
and sector-shaped holes
were considered. Based on the kinematic relation of the RV reducer and tooth contact constraints
a finite element load-bearing contact model was established for the cycloidal-pin planetary transmission with a small tooth difference. The simulated meshing characteristics
including meshing force
contact stress
number of simultaneously meshing teeth
and transmission error
were analyzed to clarify the influence mechanism of multi-hole structural parameters on meshing characteristics. With the upper-base radius
included angle between the two side edges
lower-base radius
and fillet radius of the sector-shaped holes taken as test factors
a four-factor five-level orthogonal test was designed. Range analysis was used to investigate their effects on the maximum tooth-surface contact stress and transmission error amplitude.
Results
2
The results show that
compared with the conventional simplified solid model
the multi-hole cycloidal-pin gear pair model increases the peak meshing force and peak contact stress by 35% and 13%
respectively. The number of simultaneously meshing teeth changes from 7 in the simplified solid model to a fluctuating range of 5 to 9. The transmission error amplitude of the multi-hole cycloidal-pin gear pair model is 9.86″
which is 26.6 times that of the simplified solid model. In addition to retaining the basic meshing-period characteristics
the transmission error curve shows more pronounced additional fluctuations. Range analysis indicates that the upper-base radius has the most significant effect on the maximum tooth-surface contact stress
and a smaller upper-base radius helps reduce the peak tooth-surface contact stress. The included angle between the two side edges is the main factor affecting the transmission error amplitude
and reducing this angle helps improve transmission accuracy. The lower-base radius has a relatively weak effect
whereas an appropriate increase in the fillet radius helps reduce the transmission error amplitude. These conclusions provide a basis for the forward design and structural optimization of cycloidal-pin gear pairs in high-performance RV reducers.
Han L S , Zhang Y S , Wang Y J , et al . Current status of RV reducer development in China and abroad [J]. Journal of Engineering Research and Reports , 2023 , 25 ( 8 ): 141 - 147 .
Masmoudi W , Wojtowicki J L , Petrone G , et al . Evaluating lightweight gear transmission error:a novel nonlinear finite element approach using direct constraint contact algorithm [J]. Frontiers in Mechanical Engineering , 2023 , 9 : 1228696 .
Benaïcha Y , Mélot A , Rigaud E , et al . A decomposition method for the fast computation of the transmission error of gears with holes [J]. Journal of Sound and Vibration , 2022 , 532 : 116927 .
Hong C Y , Liu M , Su N , et al . Study on the influence of gear spoke hole numbers on meshing noise [J]. Applied Sciences , 2023 , 13 ( 1 ): 511 .
Shweiki S , Rezayat A , Tamarozzi T , et al . Transmission error and strain analysis of lightweight gears by using a hybrid FE-analytical gear contact model [J]. Mechanical Systems and Signal Processing , 2019 , 123 : 573 - 590 .
Sun Z , Tang J Y , Chen S Y , et al . Dynamical modeling and characteristics analysis of tooth spalling in gear system with weight reduction structure [J]. Mechanism and Machine Theory , 2023 , 189 : 105429 .
谢学凯 , 魏冰阳 , 古德万 , 等 . 一种圆柱直齿轮槽孔减振结构仿真分析与试验研究 [J]. 机械传动 , 2023 , 47 ( 2 ): 107 - 115 .
Xie Xuekai , Wei Bingyang , Gu Dewan , et al . Simulation analysis and experimental research on a vibration damping structure of cylindrical spur gear slot holes [J]. Journal of Mechanical Transmission , 2023 , 47 ( 2 ): 107 - 115 .
崔迪 , 张迎辉 , 葛宰林 , 等 . RV减速器有限元动态仿真与接触疲劳强度设计 [J]. 机械设计 , 2019 , 36 ( 9 ): 50 - 56 .
Cui Di , Zhang Yinghui , Ge Zailin , et al . Finite-element dynamic simulation and design of contact fatigue strength for RV reducer [J]. Journal of Machine Design , 2019 , 36 ( 9 ): 50 - 56 .
杨帆 , 杨建军 , 邓效忠 , 等 . 摆线轮孔型结构对摆线轮振动特性影响分析 [J]. 机械强度 , 2023 , 45 ( 4 ): 999 - 1004 .
Yang Fan , Yang Jianjun , Deng Xiaozhong , et al . Analysis of influence of cycloid gear hole structure on the vibration characteristic of cycloidal gear [J]. Journal of Mechanical Strength , 2023 , 45 ( 4 ): 999 - 1004 .
Wu Z G , Li X , Sun Q , et al . Integrated geometric modeling,meshing behavior analysis,and experimental prototype validation of arc-cycloid external gear pairs [J]. Mechanism and Machine Theory , 2026 , 219 : 106323 .
Gao S , Zhang Y M , Li Y W , et al . Piecewise modification of cycloidal gear in RV reducer:application of spline interpolation theory and comparison with a combination modification optimization method [J]. International Journal of Precision Engineering and Manufacturing , 2025 , 26 ( 1 ): 195 - 208 .
Liu W K , Li S F , Park H S . Eighty years of the finite element method:birth,evolution,and future [J]. Archives of Computational Methods in Engineering , 2022 , 29 ( 6 ): 4431 - 4453 .
Gonzalez-Perez I , Fuentes-Aznar A . Implementation of a finite element model for stress analysis of gear drives based on multi-point constraints [J]. Mechanism and Machine Theory , 2017 , 117 : 35 - 47 .
Zhang K , Guo C X , Li Y T , et al . Contact analysis for cycloid pinwheel mechanism by isogeometric finite element [J]. Coatings , 2023 , 13 ( 12 ): 2029 .
李红勋 , 金晓辉 , 叶鹏 , 等 . 基于有限元法的高重合度摆线内齿轮副时变啮合特性研究 [J]. 机械工程学报 , 2021 , 57 ( 11 ): 206 - 219 .
Li Hongxun , Jin Xiaohui , Ye Peng , et al . Research of time-varying mesh characteristics of cycloid internal gear pair with high contact ratio based on finite element method [J]. Journal of Mechanical Engineering , 2021 , 57 ( 11 ): 206 - 219 .
王辉 , 石照耀 , 林家春 , 等 . 机器人用RV减速器多齿啮合特性研究 [J]. 哈尔滨工程大学学报 , 2020 , 41 ( 2 ): 227 - 234 .
Wang Hui , Shi Zhaoyao , Lin Jiachun , et al . Multi-tooth meshing performance of RV reducer for robot arms [J]. Journal of Harbin Engineering University , 2020 , 41 ( 2 ): 227 - 234 .
吴素珍 , 何卫东 , 张迎辉 . RV传动机构用转臂轴承的受力及接触特性分析 [J]. 华南理工大学学报(自然科学版) , 2020 , 48 ( 6 ): 25 - 33 .
Wu Suzhen , He Weidong , Zhang Yinghui . Analysis of force and contact characteristics of rotating arm bearings for RV transmissions mechanism [J]. Journal of South China University of Technology (Natural Science Edition) , 2020 , 48 ( 6 ): 25 - 33 .
Kong W C , Li X , Qian G C , et al . Integrated theoretical modeling and MASTA-based parametric simulation for contact mechanics,wear behavior,of critical bearings in RV reducers [J]. Lubricants , 2026 , 14 ( 4 ): 141 .
Li X , Chen B K , Wang Y W , et al . Mesh stiffness calculation of cycloid-pin gear pair with tooth profile modification and eccentricity error [J]. Journal of Central South University , 2018 , 25 ( 7 ): 1717 - 1731 .
Gao S , Wang J P . Optimization modelling and application scenario for cycloid-pin gear mechanism based on force transmission characteristics [J]. Forschung Im Ingenieurwesen , 2024 , 88 ( 1 ): 43 .
Zhang Y H , Huang J Y , He W D . Multi-objective optimization of cycloidal gear based on segmental modification of pressure angle [J]. Journal of Mechanical Science and Technology , 2022 , 36 ( 7 ): 3535 - 3545 .
Yun P W , Fu H D , Zhang H T , et al . Rapid design of high-end copper alloy processes combining orthogonal experiments,machine learning,and Pareto analysis [J]. Journal of Materials Research and Technology , 2025 , 36 : 1005 - 1016 .
李辉 , 徐宏海 , 吴凯 . 基于正交试验法的RV减速器传动误差分析 [J]. 机械传动 , 2017 , 41 ( 2 ): 71 - 76 .
Li Hui , Xu Honghai , Wu Kai . Analysis of transmission error of RV reducer based on orthogonal experiment [J]. Journal of Mechanical Transmission , 2017 , 41 ( 2 ): 71 - 76 .
Ji S T , Li J L , Wei T Y , et al . Study on multi-tooth meshing-in impact and optimization design of modified cycloidal pin gear transmission [J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering , 2025 , 47 ( 2 ): 69 .
Mo J Y , Luo S M , Gong X , et al . Influence of modification and shaft angle error on the meshing and mechanical performance of internal meshing planetary reducer with involute-cycloid tooth [J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering , 2026 , 48 ( 2 ): 85 .
段蕴杰 , 韩振华 , 韩小飞 , 等 . 基于LTCA的摆线针轮制造误差分析与补偿研究 [J]. 组合机床与自动化加工技术 , 2025 ( 2 ): 222 - 228 .
Duan Yunjie , Han Zhenhua , Han Xiaofei , et al . Research on transmission error and error compensation of cycloidal pinwheel based on LTCA [J]. Modular Machine Tool & Automatic Manufacturing Technique , 2025 ( 2 ): 222 - 228 .
苏建新 , 王东峰 , 徐家科 , 等 . 摆线针轮啮合刚度计算与仿真分析研究 [J]. 机械传动 , 2025 , 49 ( 4 ): 1 - 7 .
Su Jianxin , Wang Dongfeng , Xu Jiake , et al . Research on calculation and simulating analysis of cycloidal pin wheel meshing stiffness [J]. Journal of Mechanical Transmission , 2025 , 49 ( 4 ): 1 - 7 .
杜雪松 , 余自强 , 朱才朝 , 等 . RV减速器针摆传动啮合特性分析 [J]. 机械强度 , 2020 , 42 ( 1 ): 115 - 121 .
Du Xuesong , Yu Ziqiang , Zhu Caichao , et al . Analysis of meshing characteristics of pin-cycloid transmission of RV reducer [J]. Journal of Mechanical Strength , 2020 , 42 ( 1 ): 115 - 121 .
王永强 , 魏冰阳 , 徐家科 , 等 . 摆线针轮多齿啮合特性与承载接触分析方法 [J]. 中国机械工程 , 2023 , 34 ( 10 ): 1151 - 1158 .
Wang Yongqiang , Wei Bingyang , Xu Jiake , et al . Multi tooth meshing characteristics and load bearing contact analysis method of cycloidal-pin wheels [J]. China Mechanical Engineering , 2023 , 34 ( 10 ): 1151 - 1158 .
李天兴 , 夏鑫博 , 吴丹 , 等 . 考虑齿形误差影响的摆线针轮承载特性分析 [J]. 河南科技大学学报(自然科学版) , 2024 , 45 ( 1 ): 12 - 18 .
Li Tianxing , Xia Xinbo , Wu Dan , et al . Load characteristics analysis of cycloidal pin gear considering influence of tooth profile error [J]. Journal of Henan University of Science and Technology (Natural Science) , 2024 , 45 ( 1 ): 12 - 18 .
O’Shea R , Deeney P , Triantaphyllou E , et al . Weight stability intervals for multi-criteria decision analysis using the weighted sum model [J]. Expert Systems with Applications , 2026 , 296 : 128460 .
0
浏览量
0
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
京公网安备11010802024621