1.北方民族大学 机电工程学院, 宁夏 银川 750021
2.北方民族大学 电气信息工程学院, 宁夏 银川 750021
赵涛(1985— ),男,宁夏中宁人,博士,讲师;研究方向为柔索驱动并联机器人、模块化与可重构机器人等。
扫 描 看 全 文
赵涛,丁晓军,赵虎等.索杆夹角可变的3自由度欠约束并联机器人的运动学控制[J].机械传动,2022,46(12):73-78.
Zhao Tao,Ding Xiaojun,Zhao Hu,et al.Kinematics Control of 3-DOF Under-constrained Parallel Robot with Variable Cable Mast Angles[J].Journal of Mechanical Transmission,2022,46(12):73-78.
赵涛,丁晓军,赵虎等.索杆夹角可变的3自由度欠约束并联机器人的运动学控制[J].机械传动,2022,46(12):73-78. DOI: 10.16578/j.issn.1004.2539.2022.12.011.
Zhao Tao,Ding Xiaojun,Zhao Hu,et al.Kinematics Control of 3-DOF Under-constrained Parallel Robot with Variable Cable Mast Angles[J].Journal of Mechanical Transmission,2022,46(12):73-78. DOI: 10.16578/j.issn.1004.2539.2022.12.011.
柔索驱动并联机器人是一种特殊类型的并联机器人,其末端执行器由柔索替代刚性杆进行驱动。研究了一种索杆夹角可变的3自由度欠约束并联机器人,采用矢量闭环原理建立该机器人的逆运动学模型;根据拉格朗日方程,建立了该机器人的动力学模型。基于模型补偿的机器人PD控制理论,设计了该机器人的PD控制器;给定机器人末端执行器的运动轨迹,使末端执行器的位姿变化通过机器人的逆运动学转化为柔索长度的变化,以柔索长度作为控制系统的输入。实验结果验证了该机器人的逆运动学和动力学模型的正确性及控制方法的有效性。
The cable-driven parallel robot is a special type of parallel robots whose end-effector is driven by cables instead of rigid rods. A three-degree-of-freedom (3-DOF) under-constrained parallel robot with variable cable mast angle is studied. The inverse kinematics model of the robot is established by using the vector closed-loop principle. According to the Lagrange equation, the dynamics model of the robot is established. Based on the robot PD control theory of model compensation, a PD controller of the robot is designed. Given a motion trajectory of the end-effector of the robot, the pose change of the end-effector is transformed into cable length change through the inverse kinematics of the robot. The cable length is used as the input of the control system. The experimental results verify the correctness of the inverse kinematics and dynamics model of the robot and the effectiveness of the control method.
柔索驱动并联机器人索杆夹角可变逆运动学模型动力学模型机器人PD控制
Cable-driven parallel robotVariable cable mast angleInverse kinematics modelDynamics modelPD control of robot
POTT A.Cable-driven parallel robots:theory and application[J].Springer Tracts in Advanced Robotics,2018:15-43.
QIAN S,ZI B,WANG D M,et al.Development of modular cable-driven parallel robotic systems[J].IEEE access,2019,7:5541-5553.
NAN R D.Five hundred meter aperture spherical radio telescope (FAST)[J].Science in China,2006,49(2):129-148.
DUAN B Y,QIU Y Y,ZHANG F S,et al.On design and experiment of the feed cable-suspended structure for super antenna[J].Mechatronics,2009,19(4):503-509.
李国胜.四索牵引摄像机器人的建模与动力学仿真分析[D].西安:西安电子科技大学,2014:11-37.
LI Guosheng.Modeling and dynamic simulation of a four-cable-driven camera robot[D].Xi'an:Xidian University,2014:11-37.
ZHOU B,ZI B,LI Y,et al.Hybrid compound function/subinterval perturbation method for kinematic analysis of a dual-crane system with large bounded uncertainty[J].Journal of Computational and Nonlinear Dynamics,2020,16(1):014501.
ZI B,WANG N,QIAN S,et al.Design,stiffness analysis and experimental study of a cable-driven parallel 3D printer[J].Mechanism and Machine Theory,2019,132:207-222.
SHI D,ZHANG W X,ZHANG W,et al.A review on lower limb rehabilitation exoskeleton robots[J].Chinese Journal of Mechanical Engineering,2019,32(1):74.
WANG X G,MA S Y,LIN Q.Hybrid pose/tension control based on stiffness optimization of cable-driven parallel mechanism in wind tunnel test[C]//2016 2nd International Conference on Control,Automation and Robotics (ICCAR),Hong Kong,China,April 28-30,2016:75-79.
刘积彧.六索飞机自动褪喷漆并联机构的设计与优化[J].滨州学院学报,2018,34(4):15-21.
LIU Jiyu.Optimization design of a six cable-driven parallel mechanism for aircraft automatic fade-painting[J].Journal of Binzhou University,2018,34(4):15-21.
邬蓉蓉,黎大健,覃剑,等.变电站室内柔索驱动巡检机器人系统设计与运动学分析[J].电力系统保护与控制,2021,49(10):89-97.
WU Rongrong,LI Dajian,QIN Jian,et al.System design of an indoor inspection robot driven by a flexible cable in a substation[J].Power System Protection and Control,2021,49(10):89-97.
洪逸凡,谭建平.基于柔索驱动的锅炉检测机器人轨迹规划研究[J].传感器与微系统,2021,40(7):25-27.
HONG Yifan,TAN Jianping.Study on trajectory planning of cable-driven robot for boiler detection[J].Transducer and Microsystem Technologies,2021,40(7):25-27.
郭晓玲.3D打印机索驱动支撑系统的可重构研究[D].西安:西安理工大学,2019:11-24.
GUO Xiaoling.Reconfigurable research on cable drive support system of 3D printer[D].Xi'an:Xi'an University of Technology,2019:11-24.
ANSON M,ALAMDARI A,KROVI V.Orientation workspace and stiffness optimization of cable-driven parallel manipulators with base mobility[J].Journal of Mechanisms and Robotics,2017,9(3):031011.
LI C,GU X,REN H.A cable driven flexible robotic grasper with lego-like modular and reconfigurable joints[J].IEEE/ASME Transactions on Mechatronics,2017,22(6):2757-2767.
BARBAZZA L,OSCARI F,MINTO S,et al.Trajectory planning of a suspended cable driven parallel robot with reconfigurable end effector[J].Robotics and Computer-Integrated Manufacturing,2017,48:1-11.
ZHAO T,ZI B,QIAN S,et al.Algebraic method-based point-to-point trajectory planning of an under-constrained cable-suspended parallel robot with variable angle and height cable mast[J].Chinese Journal of Mechanical Engineering,2020,33(4):53-70.
刘金琨.机器人控制系统的设计与MATLAB仿真[M].北京:清华大学出版社,2016:13-20.
LIU Jinkun.Robot control system design and MATLAB simulation[M].Beijing:Tsinghua University Press,2016:13-20.
0
浏览量
3
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构