瓦面环形槽与推力轴承承载性能关系数值模拟

张文涛; 刘杨; 王东升

doi:10.16578/j.issn.1004.2539.2021.11.023

您当前的位置：

首页 >

文章列表页 >

瓦面环形槽与推力轴承承载性能关系数值模拟

试验分析 | 更新时间：2022-11-10

- 瓦面环形槽与推力轴承承载性能关系数值模拟
- Numerical Simulation of Bearing Capacity Relationship Between Tile Surface Annular Groove and Thrust Surface
- 机械传动 2021年45卷第11期页码：147-152
- 作者机构：
  
  1.长春理工大学机电工程学院，吉林长春 130022
- 作者简介：
  
  张文涛（1972— ），男，吉林长春人，博士，副教授；研究方向为摩擦与润滑、精密超精密加工与检测技术等。
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2021.11.023
  中图分类号：
扫描看全文
张文涛,刘杨,王东升.瓦面环形槽与推力轴承承载性能关系数值模拟[J].机械传动,2021,45(11):147-152.

Zhang Wentao,Liu Yang,Wang Dongsheng.Numerical Simulation of Bearing Capacity Relationship Between Tile Surface Annular Groove and Thrust Surface[J].Journal of Mechanical Transmission,2021,45(11):147-152.
张文涛,刘杨,王东升.瓦面环形槽与推力轴承承载性能关系数值模拟[J].机械传动,2021,45(11):147-152. DOI： 10.16578/j.issn.1004.2539.2021.11.023.

Zhang Wentao,Liu Yang,Wang Dongsheng.Numerical Simulation of Bearing Capacity Relationship Between Tile Surface Annular Groove and Thrust Surface[J].Journal of Mechanical Transmission,2021,45(11):147-152. DOI： 10.16578/j.issn.1004.2539.2021.11.023.

摘要

为研究瓦面环形槽对推力滑动轴承承载性能改善的优势，基于计算流体动力学（CFD）理论，建立了环形槽斜平面推力滑动轴承油膜分析模型，通过数值模拟，得到环形槽的平面区域占长比、深度和宽度对环形槽斜平面推力滑动轴承承载性能的影响规律。结果表明，推力轴承的承载力和油膜压力峰值随环形槽在平面区域的占长比的增加呈现先增大后减小的变化规律，并且随着环形槽占长比的增加，轴承温度逐渐下降；环形槽宽度一定时，深度的增加使得推力滑动轴承油膜压力分布明显改变，承载力呈现先增大后减小的变化规律；环形槽深度一定时，轴承承载力随着环形槽宽度的增加而增加；在斜平面推力滑动轴承瓦面增加特定环形槽结构，有利于提升承载性能。

Abstract

In order to study the advantages of the annular groove of the tile surface on the bearing performance of the thrust sliding bearing，based on the theory of computational fluid dynamics (CFD)，the oil film analysis model of the inclined plane thrust sliding bearing with the annular groove is established. The law of influence of depth and width on the bearing performance of annular groove inclined plane thrust sliding bearing. The results show that the bearing capacity and peak oil film pressure of the thrust bearing increase first and then decrease with the increase in the proportion of the annular groove in the plane area，and as the proportion of the annular groove increases，the bearing temperature gradually decreases. When the width of the annular groove is constant，the increase of the depth makes the oil film pressure distribution of the thrust sliding bearing change obviously，and the bearing capacity shows a change law that first increases and then decreases，the depth of the annular groove remains unchanged，and the bearing capacity increases with the increase of the width of the annular groove Increase，adding a specific annular groove structure on the inclined plane thrust sliding bearing pad surface is beneficial to improve the bearing performance.

关键词

计算流体动力学环形槽推力滑动轴承承载性能

Keywords

CFDAnnular grooveThrust journal bearingBearing capability

references

SUNG I H，LEE H S，KIM D E.Effect of surface topography onthe frictional behavior at the micro/nanoscale［J］.Wear，2003，254（10）：1019-1031.

MARCHETTO D，ROTA A，CALABRI L，et al.AFM investigation oftribological properties of nanopatterned silicon surface［J］.wear，2008，265（5/6）：577-582.

李男儿，王琳.瓦面凹槽结构参数对可倾瓦推力轴承润滑性能的影响［J］.轴承，2019（6）：6-9.

LI Naner，WANG Lin.Effect of structural parametersof bush surface groove on lubrication propertiesof tilting pad thrust bearings［J］.Bearing，2019（6）：6-9.

杨淑燕，王海峰，郭峰.表面凹槽对流体动压润滑油膜厚度的影响［J］.摩擦学学报，2011，31（3）：283-288.

YANG Shuyan，WANG Haifeng，GUO Feng.Influence of grooved surfaces onthe film thickness of hydrodynamic lubrication［J］.Tribology，2011，31（3）：283-288.

张亚伟，杨淑燕，郭峰.表面具有凹槽的平行轴承润滑性能的理论与实验研究［J］.润滑与密封，2016，41（9）：37-43.

ZHANG Yawei，YANG Shuyan，GUO Feng.Theoretical and experimentalStudies of lubrication in parallel bearing with groovedSurface［J］.Lubrication Engineering，2016，41（9）：37-43.

FU Y，JI J，BI Q.The influence of partially texturedsliderwith oriented parabolic grooves on the behavior of hydro-dynamic lubrication［J］.Tribology Transactions，2012，55（2）：210-217.

JI J，FU Y，BI Q.Influence of geometric shapes on the hydr-odynamic lubrication of a partially textured slider withmicrogrooves［J］.Journal of Tribology，2014，136（4）：041702.

CHARITOPOLOS A，FOUFLIAS D，PAPADOPOULOS C I，et al.Thermo-hydrodynamic analysis of a textured sectorpad thrust bea-ring：effects on mechanical deformations［J］.Mechanics & Industry，2014，15（5）：403-411.

PAPADOPOULOS C，HENRY Y，BOUYER J，et al.Sector-padthrust bearings with rectangular dimples：Comparisonbetween ex-periments and CFD thermohydrodynamic simulations［C］.Proceedings of the World Tribology Congress，2013：1-4.

成大先.机械设计手册-轴承［M］.北京：化学工业出版社，2004：111-112.

CHENG Daxian.Mechanical design handbook：bearing［M］.Beij-ing：Chemical Industry Press，2004：111-112.

FOUFLIAS D G，CHARITOPOULOS A G，PAPADOPOULOS C I，et al.Performance comparison between textured，pocket，and tapered-land sectorpad thrust bearings using computationalfluid dynamics thermohydrodynamic analysis［J］.Journal of Engineering Tribology，2015，229（4）：376-397.

邓礼平.推力轴承层流向紊流转变区域的理论分析［J］.润滑与密封，1997，22（4）：5-9.

DENG Liping.Theoretical analysis of transition areafrom layer flow to turbulence flow of thrust bearing［J］.Lubrication Engineering，1997，22（4）：5-9.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

高速弧齿圆柱齿轮风阻功率损失研究