非正交斜齿面齿轮弯曲强度计算方法研究

秦德润; 杨龙; 唐进元; 陈思雨

doi:10.16578/j.issn.1004.2539.2020.01.001

您当前的位置：

首页 >

文章列表页 >

非正交斜齿面齿轮弯曲强度计算方法研究

理论研究 | 更新时间：2022-11-10

- 非正交斜齿面齿轮弯曲强度计算方法研究
- Research of the Calculation Method of Bending Strength of Non-orthogonal Helical Face Gear
- 机械传动 2020年44卷第1期页码：1-6
- 作者机构：
  
  1.中南大学高性能复杂制造国家重点实验室，湖南长沙 410083
  2.中国船舶集团有限公司第七○三研究所，黑龙江哈尔滨 150078
- 作者简介：
  
  秦德润（1993— ），男，贵州遵义人，在读硕士研究生，主要从事面齿轮动力学研究。
  陈思雨（1981— ），男，湖北通山县人，副教授，博士生导师，研究方向为齿轮非线性动力学、故障诊断。
- 基金信息：
  
  国家重点研发计划项目(2018YFB2001700)
- DOI：10.16578/j.issn.1004.2539.2020.01.001
  中图分类号：
扫描看全文
秦德润,杨龙,唐进元等.非正交斜齿面齿轮弯曲强度计算方法研究[J].机械传动,2020,44(01):1-6.

Qin Derun,Yang Long,Tang Jinyuan,et al.Research of the Calculation Method of Bending Strength of Non-orthogonal Helical Face Gear[J].Journal of Mechanical Transmission,2020,44(01):1-6.
秦德润,杨龙,唐进元等.非正交斜齿面齿轮弯曲强度计算方法研究[J].机械传动,2020,44(01):1-6. DOI： 10.16578/j.issn.1004.2539.2020.01.001.

Qin Derun,Yang Long,Tang Jinyuan,et al.Research of the Calculation Method of Bending Strength of Non-orthogonal Helical Face Gear[J].Journal of Mechanical Transmission,2020,44(01):1-6. DOI： 10.16578/j.issn.1004.2539.2020.01.001.

摘要

关于面齿轮弯曲强度计算尚未见到解析计算方法与公式的相关文献。为此，基于齿面接触分析原理，推导弯曲力臂长度计算公式，参考锥齿轮弯曲强度计算标准（ISO 10300（3）:2014），提出非正交斜齿面齿轮齿根弯曲强度解析计算方法。以某一参数面齿轮传动副为例，利用Abaqus有限元软件进行齿根弯曲强度计算，提取非正交斜齿面齿轮齿根弯曲应力值，将有限元结果与解析计算的结果进行对比，两者误差为8.5%左右，表明提出的非正交斜齿面齿轮齿根弯曲应力计算方法正确可行。研究工作解决了面齿轮弯曲强度计算尚无解析计算公式问题，在进一步细化完善后，有望形成基础的面齿轮弯曲强度设计计算公式。

Abstract

There is no analytical calculation method and formula for the calculation of the bending strength of the face gear.For this reason，based on the principle of tooth surface contact analysis，the formula for calculating the length of the bending arm is derived，reference the calculation standard （ISO 10300（3）：2014） of bevel gear bending strength，an analytical calculation method for the root bending strength of non-orthogonal helical face gear is proposed.Taking a parameter face gear transmission pair as an example，the Abaqus finite element software is used to calculate the root bending strength，and the root bending stress value of the non-orthogonal helical face gear is extracted.The finite element results are compared with the analytical calculation results，the error is about 8.5%.The results show that the calculation method of the calculation method of the root bending stress of non-orthogonal helical face gears is correct and feasible.The problem that the calculation of the bending strength of the face gear has no analytical formula is solved.After refinement and perfection，it is expected to form a basic calculation formula for the bending strength design of the face gear.

关键词

弯曲强度斜齿面齿轮非正交计算方法

Keywords

Bending strengthHelical face gearNon-orthogonalCalculation method

references

LITVIN F L，FUENTES A，ZANZI C，et al.Design，generation，and stress analysis of two versions of geometry of face-gear drives[J].Mechanism and Machine Theory，2002，37（10）:1179-1211.

GUINGAND M，VAUJANY J P，JACQUIN C Y，et al.Quasi-static analysis of a face gear under torque[J].Computer Methods in Applied Mechanics and Engineering，2005，194（39/40/41）:4301-4318.

ZANZI C，PEDRERO J I.Application of modified geometry of face gear drive[J].Computer Methods in Applied Mechanics and Engineering，2005，194（27/28/29）:3047-3066.

LITVIN F L，FUENTES A，ZANZI C，et al.Face-gear drive with spur involute pinion:geometry，generation by a worm，stress analysis[J].Computer Methods in Applied Mechanics and Engineering，2002，191（25/26）:2785-2813.

BUCKINGHAM E.Analytical mechanics of gears[M].Chicago:Courier Corporation，1988:312-320.

KISSLING U，BEERMANN S.Face gears:geometry and strength[J].Gear Technology，2007（1）:54-61.

黄丽娟，朱如鹏.基于ANSYS的斜齿面齿轮传动的弯曲应力分析[J].机械传动，2009，33（3）：91-93.

HUANG Lijuan，ZHU Rupeng.Bending stress analysis of helical face-gear drive based on ANSYS[J].Journal of Mechanical Transmission，2009，33(3):91-93.

刘艳平.直齿—面齿轮加载接触分析及弯曲应力和接触应力计算方法研究[D].长沙：中南大学，2012:68-69.

LIU Yanping.The loaded tooth contact analysis and bending stress and contact stress calculating method research of face gear drive with spur involute pinion[D].Changsha:Central South University，2012:68-69.

周辉俊.正交面齿轮传动的弯曲应力计算方法及试验研究[D].南京：南京航空航天大学，2013:49.

ZHOU Huijun.Research on method of calculation and experiment of bending stress of orthogonal face gear drive[D].Nanjing:Nanjing University of Aeronautics and Astronautics，2013:49.

International Organization for Standardization.Calculation of load capacity of spur and helical gears-part 3:calculation of tooth bending strength:ISO 6336(3):2006[S].Geneva:International Organization for Standardization，2006:2.

International Organization for Standardization.Calculation of load capacity of bevel gears-part 3:calculation of tooth root strength:ISO 10300(3):2014[S].Geneva:International Organization for Standardization，2014：3-32.

黄龙.非正交面齿轮传动系统的动力学分析及修形研究[D].哈尔滨：哈尔滨理工大学，2014:9-10.

HUANG Long.Research on dynamic analysis and tooth profile modification of non-orthogonal face gear transimission system[D].Harbin:Harbin University of Science and Technology，2014:9-10.

王志，刘建炜，刘锐，等.面齿轮传动国内研究进展[J].机械设计与制造，2012（3）：219-221.

WANG Zhi，LIU Jianwei，LIU Rui，et al.Face gear drive and its research developments in domestic[J].Journal of Machinery Design & Manufacture，2012（3）：219-221.

PENG M，DESMIDT H，SARIBAY Z B，et al.Parametric instability of face-gear drives with a spur pinion[Z].67th American Helicopter Society International Annual Forum，2011:2478-2488.

CHEN S，TANG J，CHEN W，et al.Nonlinear dynamic characteristic of a face gear drive with effect of modification[J].Meccanica，2014（49）:1023-1025.

International Organization for Standardization.Calculation of load capacity of bevel gears-Part 1:Introduction and general influence factors:ISO 10300(1):2014[S].Geneva:International Organization for Standardization，2014：21.

MICHAEL O，SIMEON K.Finite element applications a practical guide to the FEM process[M].Berlin:Springer，2017:384.

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

暂无数据