链轮渗碳淬火出现托氏体的原因与控制

刘毅; 张孟九; 逄宁宁

doi:10.16578/j.issn.1004.2539.2018.05.030

您当前的位置：

首页 >

文章列表页 >

链轮渗碳淬火出现托氏体的原因与控制

试验分析 | 更新时间：2022-10-20

- 链轮渗碳淬火出现托氏体的原因与控制
- Reason and Control of the Emergence of the Troostite in Sprocket Carburizing Quenching
- 机械传动 2018年42卷第5期页码：148-150
- 作者机构：
  
  1. 青岛征和工业股份有限公司
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.05.030
  中图分类号：
扫描看全文
[1]刘毅,张孟九,逄宁宁.链轮渗碳淬火出现托氏体的原因与控制[J].机械传动,2018,42(05):148-150+155.

Liu Yi, Zhang Mengjiu, Pang Ningning. Reason and Control of the Emergence of the Troostite in Sprocket Carburizing Quenching[J]. 2018,42(5):148-150.
[1]刘毅,张孟九,逄宁宁.链轮渗碳淬火出现托氏体的原因与控制[J].机械传动,2018,42(05):148-150+155. DOI： 10.16578/j.issn.1004.2539.2018.05.030.

Liu Yi, Zhang Mengjiu, Pang Ningning. Reason and Control of the Emergence of the Troostite in Sprocket Carburizing Quenching[J]. 2018,42(5):148-150. DOI： 10.16578/j.issn.1004.2539.2018.05.030.

摘要

采用Q235B热轧态原材料,在经渗碳淬火后的金相检验过程中,链轮次表层出现托氏体层,此层严重降低了表层与基体的结合力,并在交界处产生显微裂纹,影响了链轮的抗冲击性能和疲劳强度。通过实验找出了产生托氏体层的原因,并进行了改善,消除了淬火时产生的托氏体层,提升链轮的整体性能。

Abstract

In the process of the metallographic examination,Q235 B hot-rolled raw material appeared the troostite on the sub-surface of the sprocket after being carburized quenched. The binding force between the surface and the substrate is significantly reduced by this layer due to the microcracks at the junction of the two.In addition,the impact resistance and fatigue strength of the sprocket are also affected. The reason for the formation of the troostite is found by the experiment and the improvement is conducted. The troostite produced in quenching is eliminated and the overall performance of the sprocket is enhanced.

关键词

链轮渗碳淬火托氏体结合力疲劳强度

Keywords

SprocketCarburizing quenchingTroostiteBinding forceFatigue strength

references

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

基于非线性接触的风电机组主轴疲劳强度影响因素研究

新能源悬臂型轮边减速器箱体结构强度研究

链轮齿厚对矿用刮板输送机链传动系统的固有频率影响分析

变载荷激励下含裂纹风电行星轮系疲劳强度分析

齿轮内在品质对齿轮强度和寿命的影响