Research on Transmission Error of Hypoid Gear based on Real Tooth Surface

Yimin Mo; Renjie Mo; Qiming Li; Jie Liu; Junjian Yang; Yecai Huang

doi:10.16578/j.issn.1004.2539.2022.01.002

您当前的位置：

首页 >

文章列表页 >

Research on Transmission Error of Hypoid Gear based on Real Tooth Surface

Theory·Reserach | 更新时间：2022-09-23

- Research on Transmission Error of Hypoid Gear based on Real Tooth Surface
- Journal of Mechanical Transmission Vol. 46, Issue 1, Pages: 19-26(2022)
- 作者机构：
  
  1.武汉理工大学机电工程学院，湖北武汉 430070
  2.柳州五菱汽车工业有限公司，广西柳州 545007
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2022.01.002
  CLC：
扫描看全文
莫易敏,莫仁杰,李其明等.基于真实齿面的准双曲面齿轮传动误差研究[J].机械传动,2022,46(01):19-26.

Mo Yimin,Mo Renjie,Li Qiming,et al.Research on Transmission Error of Hypoid Gear based on Real Tooth Surface[J].Journal of Mechanical Transmission,2022,46(01):19-26.
莫易敏,莫仁杰,李其明等.基于真实齿面的准双曲面齿轮传动误差研究[J].机械传动,2022,46(01):19-26. DOI： 10.16578/j.issn.1004.2539.2022.01.002.

Mo Yimin,Mo Renjie,Li Qiming,et al.Research on Transmission Error of Hypoid Gear based on Real Tooth Surface[J].Journal of Mechanical Transmission,2022,46(01):19-26. DOI： 10.16578/j.issn.1004.2539.2022.01.002.

摘要

针对运用理论设计的齿轮进行仿真而运用实际生产的齿轮进行滚检验证测试所造成的评价标准不一致的问题，通过NURBS曲面拟合的方法重新构造真实齿轮面，在CATIA软件中进行了三维模型的构造。利用Abaqus软件对真实齿面的准双曲面齿轮传动误差进行分析，对比真实齿面啮合和纯理论齿面啮合的传动误差，验证了真实齿面误差的存在及其对传动误差的消极影响。改变齿轮的安装误差发现，轴交角误差、小轮安装距误差、偏置距误差和大轮安装距误差对传动误差的影响依次减小，通过滚检机实验验证了真实齿面仿真模型的合理性。

Abstract

Aiming at the inconsistency evaluation standards caused by using the gear designed by theory for simulation and using the gear produced by actual production for roll inspection certificate test，by using the NURBS surface fitting method，the real tooth surface is reconstructed and the construct of the 3D model in CATIA software is carried out. The Abaqus software is used to analyze the error of the hypoid gear transmission of the real tooth surface，and the transmission error of the real tooth surface meshing and the pure theoretical tooth surface meshing is compared，the existence of real tooth surface error and its negative influence on transmission error are verified. Changing the installation error of the gear found that the influence of the shaft angle error，the small wheel installation distance error，the offset distance error and the large wheel installation distance error on the transmission error decreased in turn. The rationality of the real tooth profile simulation model is verified by the rolling machine experiment.

关键词

准双曲面齿轮真实齿面传动误差安装误差敏感性

Keywords

Hypoid gearReal tooth surfaceTransmission errorInstallation errorSensitivity

references

方宗德，刘涛，邓效忠.基于传动误差设计的弧齿锥齿轮啮合分析［J］.航空学报，2002（3）：226-230.

FANG Zongde，LIU Tao，DENG Xiaozhong.Tooth contact analysis of spiral bevel gears based on the design of transmission error［J］.Acta Aeronautic ET Astronautica Sinica，2002（3）：226-230.

曹雪梅，周彦伟，邓效忠，等.弧齿锥齿轮的传动误差、重合度和噪声的关系［J］.机械传动，2003（2）：43-45.

CAO Xuemei，ZHOU Yanwei，DENG Xiaozhong，et al.Relationship between transmission error，coincidence degree and noise of spiral bevel gear［J］.Journal of Mechanical Transmission，2003（2）：43-45.

邓效忠，徐爱军，张静，等.齿距啮合偏差对准双曲面齿轮传动误差的影响［J］.航空动力学报，2013，28（3）：597-602.

DENG Xiaojun，XU Aijun，ZHANG Jing，et al.Effect of meshed pitch deviation on transmission error in hypoid gears［J］.Journal of Aerospace Power，2013，28（3）：597-602.

刘光磊，樊红卫，谷霁红，等.航空弧齿锥齿轮低噪声和低安装误差敏感性设计［J］.航空发动机，2010，36（2）：9-12.

LIU Guanglei，FAN Hongwei，GU Jihong，et al.Sensitivity design of low noise and installation error for aero spiral bevel gear［J］.Aeroengine，2010，36（2）：9-12.

SIMON V.Design of face-hobbed spiral bevel gears with reduced maximum tooth contactpressure and transmission errors［J］.Chinese Journal of Aeronautics，2013，26（3）：777-790.

SIMON V. Design and manufacture of spiral bevel gears with reduced transmission errors［J］.Journal of Mechanical Design，2009，131（4）：041007.

森川邦彦，小森雅晴，永田真範，等.コニカルギヤのかみ合い伝達誤差解析法［J］.日本機械学会論文集，2012，78（791）：270-280.

MORIKAWA K，KOMORI M，NAGATA M，et al.Transimission error analysis of conical involute gears［J］.The Japan Society of Mechanical Engineers，2012，78（791）：270-280.

王星，方宗德，牟彦铭，等.HGT准双曲面齿轮承载传动误差的优化设计［J］.振动与冲击，2017，36（8）：34-40.

WANG Xing，FANG Zongde，MOU Yanming，et al.Optimization design of loaded transmission error for HGT hypoid gear drives［J］.Journal of Vibration and Shock，2017，36（8）：34-40.

蒋进科，方宗德，苏进展.基于承载传动误差幅值最小的斜齿轮齿面修形优化设计［J］.航空动力学报，2013，28（7）：1637-1643.

JIANG Jinke，FANG Zongde，SU Jinzhan.Optimal design of modified helical gear tooth surfaces based on minimum amplitude of loaded transmission error［J］.Journal of Aerospace Power，2013，28（7）：1637-1643.

汪中厚，王杰，王巧玲，等.基于有限元法的螺旋锥齿轮传动误差研究［J］.振动与冲击，2014，33（14）：165-170.

WANG Zhonghou，WANG Jie，WANG Qiaoling，et al.Transmission error of spiral bevel gear based on finite element method［J］.Journal of Vibration and Shock，2014，33（14）：165-170.

陈燕丽.NURBS复杂自由曲面造型方法的研究［D］.西安：长安大学，2014：32-42.

CHEN Yanli.Study on modeling method of NURBS complex free surface［D］.Xi'an：Chang'an University，2014：32-42.

JUNG H B，KIM K.A new parameterisation method for NURBS surface interpolation［J］.International Journal of Advanced Manufacturing Technology，2000，16（11）：784-790.

皮格，蒂勒.非均匀有理B样条［M］.赵罡，穆国旺，王拉柱，译.北京：清华大学出版社，2010：86-93.

LES Piegl，WAYNE Tiller.Non-uniform rational B-spline［M］.ZHAO G，MU G W，WANG L Z，Jr.Beijing：Tsinghua University Press，2010：86-93.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effects of Installation Error on Tooth Surface Contact Characteristic of a Nutation Drive with Double Circular-arc Spiral Bevel Gear

Research of Bump Detection Method of Spiral Bevel Gear Tooth Surface based on Gear Contact Analysis

Research on Gear Modification and Simulation of Hybrid Transmission

Influence of Error Factors on Transmission Contact for Spiral Bevel Gears

Structure Design and Simulation Analysis of the Dynamic Inspection Instrument for Middle and Large Worm Gear Pairs

Related Author

No data

Related Institution

School of Mechanical Engineering and Automation，Fuzhou University

School of Mechatronics Engineering, Henan University of Science and Technology

Henan Collaborative Innovation Center of Manufacture of Advanced Machinery and Equipment, Henan University of Science and Technology

College of Intelligent Manufacturing, Fujian Polytechnic of Information Technology

School of Mechanical and Automotive Engineering, Fujian University of Technology

⁰