Analysis of Meshing Temperature of Plastic Gear based on the Multi Heat Source of Frictional Heat Flux and Hysteresis Heat Flux

Guoda Yu; Huaiju Liu; Caichao Zhu; Zehua Lu; Peitang Wei

doi:10.16578/j.issn.1004.2539.2021.02.002

您当前的位置：

首页 >

文章列表页 >

Analysis of Meshing Temperature of Plastic Gear based on the Multi Heat Source of Frictional Heat Flux and Hysteresis Heat Flux

Theory·Reserach | 更新时间：2022-11-10

- Analysis of Meshing Temperature of Plastic Gear based on the Multi Heat Source of Frictional Heat Flux and Hysteresis Heat Flux
- Journal of Mechanical Transmission Vol. 45, Issue 2, Pages: 6-15(2021)
- 作者机构：
  
  1.重庆大学机械传动国家重点实验室，重庆 400044
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2021.02.002
  CLC：
扫描看全文
余国达,刘怀举,朱才朝等.基于摩擦热流-滞后热通量多热源的塑料齿轮啮合温度研究[J].机械传动,2021,45(02):6-15.

Yu Guoda,Liu Huaiju,Zhu Caichao,et al.Analysis of Meshing Temperature of Plastic Gear based on the Multi Heat Source of Frictional Heat Flux and Hysteresis Heat Flux[J].Journal of Mechanical Transmission,2021,45(02):6-15.
余国达,刘怀举,朱才朝等.基于摩擦热流-滞后热通量多热源的塑料齿轮啮合温度研究[J].机械传动,2021,45(02):6-15. DOI： 10.16578/j.issn.1004.2539.2021.02.002.

Yu Guoda,Liu Huaiju,Zhu Caichao,et al.Analysis of Meshing Temperature of Plastic Gear based on the Multi Heat Source of Frictional Heat Flux and Hysteresis Heat Flux[J].Journal of Mechanical Transmission,2021,45(02):6-15. DOI： 10.16578/j.issn.1004.2539.2021.02.002.

摘要

啮合温度影响塑料齿轮服役过程中的疲劳、磨损、噪声等服役行为，在塑料齿轮的力学响应和性能预测时不可忽略。为预测塑料齿轮的啮合温度，考虑聚甲醛（POM）材料的温度-模量效应和摩擦热流-滞后热通量多热源效应，建立了塑料齿轮啮合温度场有限元数值模型。基于POM齿轮副热黏弹接触分析，获取摩擦热流和滞后热通量作为热源；通过啮合温度与材料弹性模量耦合迭代，获取考虑温度-模量效应后的齿轮稳态啮合温度和齿面闪温。稳态啮合温度和闪温分析结果分别与试验和Blok理论结果吻合良好。研究结果表明，干运行条件下滞后生热温升对稳态啮合温度影响较小，摩擦生热温升是塑料齿轮稳态啮合温度的主要组成部分。

Abstract

The meshing temperature of plastic gear affects the mechanical behaviors such as fatigue， wear and noise， which should not be ignored in the mechanical response and performance prediction of plastic gear. In order to predict the meshing temperature of plastic gears， a finite element numerical model of plastic gear temperature field is established considering the temperature-modulus effect of POM material and the multi-heat sources effect of frictional heat and hysteresis heat flux. Based on POM thermo-viscoelastic contact analysis， frictional heat flow and hysteresis loss heat flow are obtained as heat sources. Through the iterative calculation of the interaction between the steady meshing temperature and elastic modulus of plastic gear， the steady meshing temperature and tooth surface flash temperature are obtained. The steady meshing temperature results are in good agreement with the test results， and the flash temperature is in good agreement with the Blok theory. It is found that the temperature rise of hysteresis loss heat has little effect on the steady meshing temperature under dry condition， while the temperature rise caused by friction is the main component of the steady running temperature of plastic gear.

关键词

塑料齿轮滞后生热稳态啮合温度闪温

Keywords

Plastic gearHysteresis loss heatSteady meshing temperatureFlash temperature

references

SENTHILVELAN S，GNANAMOORTHY R.Effect of gear tooth fillet radius on the performance of injection molded Nylon 6/6 gears［J］.Materials and Design，2004，27（8）：632-639.

ERIC L，MICHELE G，JEAN-PIERRE D V，et al.A new experimental approach for measuring thermal behaviour in the case of Nylon 6/6 cylindrical gears［J］.Polymer Testing，2010，29（8）：1041-1051.

MAO K，LI W，HOOKE C J，et al.Polymer gear surface thermal wear and its performance prediction［J］.Tribology International，2010，43（1/2）：433-439.

FERNANDES C，ROCHA D M，MARTINS R C，et al.Hybrid polymer gear concepts to improve thermal behavior［J］.Journal of Tribology，2019，141（3）：032201.

LU Z H，LIU H J，ZHU C C，et al.Identification of failure modes of a PEEK-steel gear pair under lubrication［J］.International Journal of Fatigue，2019，125：342-348.

YU G D.，LIU H.J，ZHU C.C，et al.An experimental investigation on the wear of lubricated steel against PEEK gears［J］.Journal of Tribology，2020，142（4）：041702.

LU Z H，LIU H J，WEI P T，et al.The effect of injection molding lunker defect on the durability performance of polymer gears［J］.International Journal of Mechanical Science，2020，145（5）：111-116.

LOKESH K S，THOMAS P，RAVI S M.Evaluation of mechanical properties and wear characterization of polymer composites under varying temperature conditions：a review［J］.International Journal of Engineering and Information systems，2017，1（4）：64-68.

LAURENT C，SIMON J.Modelling the effect of temperature on the probabilistic stress-life fatigue diagram of glass fibre–polymer composites loaded in tension along the fibre direction［J］.Journal of Composite Materials，2018，52（2）：207-224.

MYSHKIN N K，PETROKOVETS M I，KOVALEV A V.Tribology of polymers：adhesion，friction，wear，and mass-transfer［J］.Tribology International，2005，38（11/12）：910-921.

CHRISTIAN H，CHRISTOPHER I，PETER O T，et al.Potential of oil-lubricated cylindrical plastic gears［J］.Journal of Advanced Mechanical Design，Systems，and Manufacturing，2018，12（1）：17-00224.

MAO K，HOOKE C J，WALTON D.The wear behaviour of polymer composite gears［J］.Journal of Synthetic Lubrication，1996，12（4）：337-345.

MAO K.A new approach for polymer composite gear design［J］.Wear，2007，262（3/4）：432-441.

MAO K，LANGLOIS P，HU Z，et al.The wear and thermal mechanical contact behaviour of machine cut polymer gears［J］.Wear，2015，332/333：822-826.

KALIN M，KUPEC A.The dominant effect of temperature on the fatigue behaviour of polymer gears［J］.Wear，2017，376/377：1339-1346.

YAKUT R，DÜZCÜKOLU H D，DEMIRCI M I.The load capacity of PC/ABS spur gears and investigation of gear damage［J］.Archives of Materials Science and Engineering，2009，40（1）：41-46.

BOTJAN T，SIMON K，GORAZD H，et al.Experimental failure analysis of S-polymer gears［J］.Engineering Failure Analysis，2020，111：104496.

HOSKINS T J，DEARN K D，KUKUREKA S N，et al.Acoustic noise from polymer gears-a tribological investigation［J］.Materials & Design，2011，32（6）：3509-3515.

HOOKE C J，MAO K，WALTON D，et al.Measurement and prediction of the surface temperature in polymer gears and its relationship to gear wear［J］.Journal of Tribology，1993，115：119-124.

MAO K.A numerical method for polymer composite gear flash temperature prediction［J］.Wear，2007，262（11/12）：1321-1329.

CARLOS M C G，FERNANDES D M P，ROCHA R C M，et al.Finite element method model to predict bulk and flash temperatures on polymer gears［J］.Tribology International，2018，120：255-268.

BORUT Č，JOŽE D，JOŽE T.Semi-analytical flash temperature model for thermoplastic polymer spur gears with consideration of linear thermo-mechanical material characteristics［J］.Journal of Computational Design and Engineering，2019，6（4）：617-628.

VICTOR R C，FRANCISCO S M.A 2D finite element based approach to predict the temperature field in polymer spur gear transmissions［J］.Mechanism and Machine Theory，2019，133：195-210.

陆松，孟惠荣.塑料齿轮的热分析［J］.塑料，2003，32（5）：58-60.

LU Song，MENG Huirong.Thermal analysis of plastic gear［J］.Plastics，2003，32（5）：58-60.

Polyplastics Co.，Ltd.POM resin Homopolymer vs.Copolymer［DB/OL］.2019：6-7.［2020-04-16］.https：//www.polyplastics.com/en/product/lines/diff2pom/index.vmhttps://www.polyplastics.com/en/product/lines/diff2pom/index.vm

智杰颖，路洪丽，王海庆，等.基于广义Maxwell模型的轮胎橡胶动态压缩性能分析［J］.高分子学报，2016（7）：887-894.

ZHI Jieying，LU Hongli，WANG Haiqing，et al.Dynamic compression performance analysis of tire rubber based on generalized Maxwell model［J］.Acta Polymerica Sinica，2016（7）：887-894.

樊鹏玄，陈务军，赵兵，等.基于广义Maxwell模型的形状记忆聚合物力学本构［J］.上海交通大学学报，2018，52（8）：969-975.

FAN Pengxuan，CHEN Wujun，ZHAO Bing，et al.Mechanical constitution of shape memory polymer based on generalized Maxwell model［J］.Journal of Shanghai Jiaotong University，2018，52（8）：969-975.

金日光，华幼卿.高分子物理［M］.3版.北京：化学工业出版社，2007：184-188.

JIN Riguang，HUA Youqing.Polymer physics［M］.3rd ed.Beijing：Chemical Industry Press，2007：184-188.

VEREIN DEUTSCHER INGENIEURE.Thermoplastische Zahnräder Stirnradgetriebe Tragfähigkeitsberechnung：VDI 2736 Blatt 1［S］.München：Verlag des Vereins Deutscher Ingenieure，2016：56-57.

刘鸿文.材料力学Ⅰ［M］.4版.北京：高等教育出版社，2004.37-39.

LIU Hongwen.Mechanics of materials Ⅰ［M］.4th ed.Beijing：Higher Education Press，2004：37-39.

LI W，TIAN J.Unsteady-state temperature field and sensitivity analysis of gear transmission［J］.Tribology International，2017，116：229-243.

PATIR N，CHENG H S.Prediction of the bulk temperature in spur gears based on finite element temperature analysis［J］.ASLE Transactions，2008，22（1）：25-36.

HANDSCHUH R F.Thermal behavior of spiral bevel gears［D］.Cleveland：Case western Reserve University，1993：93-100.

BLOK H.The flash temperature concept［J］.Wear，1963，6（6）：483-494.

ALJAŽ P，JOŽE T.An accelerated multilevel test and design procedure for polymer gears［J］.Materials & Design，2015，65：961-973.

MAO K，DAVE G，RAMKUMAR R，et al.The wear resistance improvement of fibre reinforced polymer composite gears［J］.Wear，2019，426-427：1033-1039.

SHI Y，YAO Y，FEI J.Analysis of bulk temperature field and flash temperature for locomotive traction gear［J］.Applied Thermal Engineering，2016，99：528-536.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Fatigue Life Analysis of the Plastic Helical Gear and Steel Worm Transmission Mechanism

Design and Experiment Research of Accelerated Fatigue Life Tester for Plastic Gear

Multi-condition and Multi-objective Modification Optimization Design of Spur Gear

Analysis of Flash Temperature Characteristic of the Roller Enveloping End Face Engagement Worm Drive

Development of Transmission Error Dynamic Testing Machine for Plastic Gear

Related Author

No data

Related Institution

School of Mechanical and Electrical Engineering, Jiangxi University of Science and Technology

Beijing Engineering Research Center of Precision Measurement Technology and Instruments，Faculty of Materials and Manufacturing，Beijing University of Technology

Shenzhen Zhaowei Machinery & Electronics Co.， Ltd.

AECC Hunan Aviation Powerplant Research Institute

School of Mechanical Engineering， Chengdu University

⁰