Study on the Anti Scuffing Performance of Gear based on Tooth Flank Phosphate

Xuhu Wang; Dongfei Wang; Lü Pangong; Chengtian Ma; Xiaopeng Dou; Yankun Zhang

doi:10.16578/j.issn.1004.2539.2020.11.022

您当前的位置：

首页 >

文章列表页 >

Study on the Anti Scuffing Performance of Gear based on Tooth Flank Phosphate

Test·Analysis | 更新时间：2022-11-10

- Study on the Anti Scuffing Performance of Gear based on Tooth Flank Phosphate
- Journal of Mechanical Transmission Vol. 44, Issue 11, Pages: 134-138(2020)
- 作者机构：
  
  1.郑州电力高等专科学校电气工程学院，河南郑州 450000
  2.郑州机械研究所有限公司国家齿轮产品质量监督检验中心，河南郑州 450052
  3.宝鸡石油机械有限责任公司生产安全部，陕西宝鸡 721000
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2020.11.022
  CLC：
扫描看全文
王绪虎,王东飞,吕泮功等.基于齿面磷化的齿轮抗胶合性能试验[J].机械传动,2020,44(11):134-138.

Wang Xuhu,Wang Dongfei,Pangong Lü,et al.Study on the Anti Scuffing Performance of Gear based on Tooth Flank Phosphate[J].Journal of Mechanical Transmission,2020,44(11):134-138.
王绪虎,王东飞,吕泮功等.基于齿面磷化的齿轮抗胶合性能试验[J].机械传动,2020,44(11):134-138. DOI： 10.16578/j.issn.1004.2539.2020.11.022.

Wang Xuhu,Wang Dongfei,Pangong Lü,et al.Study on the Anti Scuffing Performance of Gear based on Tooth Flank Phosphate[J].Journal of Mechanical Transmission,2020,44(11):134-138. DOI： 10.16578/j.issn.1004.2539.2020.11.022.

摘要

对同批次生产的齿面未磷化和齿面磷化直齿圆柱齿轮分成未磷化齿轮组；单磷化齿轮组和双磷化齿轮组，分别在齿轮接触疲劳试验机上进行胶合性能试验；同时，利用齿轮测量中心D80检测的试验齿轮的螺旋线曲线来准确计算胶合面积和胶合沟痕的深度。试验表明：在相同运转条件下，磷化齿轮出现胶合失效时的加载转矩远大于未磷化齿轮的；磷化齿轮出现胶合失效时的运转次数远多于未磷化齿轮的。由此得出，齿面磷化能显著提高齿轮的抗胶合性能。

Abstract

The unphosphorized and phosphatized spur gears produced in the same batch are divided into three groups，the unphosphorized gear group， the single phosphated gear group and the double phosphated gear group， the scuffing performance test is carried out in groups on the gear contact fatigue tester. At the same time， the helix curve of the test gears detected by the gear measuring center D80 is used to accurately calculate the gluing area and the depth of the gluing groove mark. The results show that， under the same operating conditions， the loading torque of the phosphated gear is much greater than that of the unphosphorized gear， and the operating time of the phosphated gear is much more than that of the unphosphorized gear. It is concluded that， phosphating can significantly improve the anti scuffing performance of gears.

关键词

圆柱齿轮齿面磷化抗胶合接触疲劳试验机

Keywords

Cylindrical gearTooth flank phosphateAnti scuffingContact fatigue tester

references

王希贵.船用动力后传动系统齿轮抗胶合承载性能分析及实验研究［D］.黑龙江：哈尔滨工业大学，2017：11-13.

WANG Xigui.Analysis and experiment research on gear anti scuffing load bearing performance of marine power rear transmission system［D］.Heilongjiang：Harbin University of Technology，2017：11-13.

MARTINS R，AMARO R，SEABRA J.Influence of low friction coatings on the scuffing load capacity and efficiency of gears［J］.Tribology International，2008，41：234-243.

TUSZYNSKIN W，MICHALCZEWSKI R，SZCZEREK M，et al.A new scuffing shock test method for the determination of the resistance to scuffing of coated gears［J］.Archives of Civil and Mechanical Engineering，2012，12：436-445.

IMREK H，UNUVAR A.Investigation of influence of load and velocity on scoring of addendum modified gear teeth profiles［J］.Mechanism and Machine Theory，2009，44（5）：938-948.

LI S.Effects of misalignment error，teeth modifications and transmitted torque on teeth engagements of a pair of spur gears［J］.Mechanism and Machine Theory，2015，83：125-136.

CHEN Z G，SHAO Y M.Mesh stiffness calculation of a spur gear pair with teeth profile modification and teeth root crack［J］.Mechanism and Machine Theory，2013，62：63-74.

BARBIERI M，BONORI G，PELLICANO F.Corrigendum to：Optimum profilemodifications of spur gears by means of genetic algorithms［J］.Journal of Sound and Vibration，2012，331：4825-4829.

WECK M，HURASKY-SCHONWERTH O.Service behavior of PVD-coated gearing lubricated with biodegradable synthetic wster oils［J］.Gear Technology，2004（1/2）：34-40．

贾森，陈勇，臧立彬，等.基于磷化涂层表面改性齿轮的温度场特性研究［J］.机械传动，2018，42（4）：23-24.

JIA Sen，CHEN Yong，ZANG Libin，et al.Study on temperature field characteristic of surfacemodified gear based on phosphating coating［J］.Journal of Mechanical Transmission，2018，42（4）：23-24.

李文平，赵冉.磷化处理对齿轮材料摩擦磨损特性的影响［J］.材料应用，2016（9）：57-58.

LI Wenping，ZHAO Ran.Effect of phosphating treatment on friction and wear characteristics of gear materials［J］.Journal of Material Application，2016（9）：57-58.

中华人民共和国国家发展和改革委员会.机械行业标准书号：JB/T 5664-2007［S］.北京：机械工业出版社，2007：3.

National Development and Reform Commission of the people's Republic of China.Mechanical industry standard book No.：JB/T 5664-2007［S］.Beijing：Mechanical Industry Press，2007：3.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Fatigue Life Prediction Model of Cylindrical Gears Based on the Energy Accumulation Curve

Comparative Study on Calculation Standards for Scuffing Load Capacity of Cylindrical Involute Gears

Deviation Evaluation Method of Cylindrical Gear Tooth Surface Based on the Coordinates of the Actual Tooth Surface Points

Research of Axial Crowning Modification of Involute Cylindrical Gear

Related Author

No data

Related Institution

School of Mechanical-Electronic and Vehicle Engineering, Beijing University of Civil Engineering and Architecture

State Key Laboratory of Mechanical Transmissions, Chongqing University

China Aviation Development Sichuan Gas Turbine Research Institute, Aero Engine Corporation of China

School of Mechatronics Engineering, Henan University of Science and Technology

Student Affair Office, Henan University of Science and Technology

⁰