Analysis of the Influence of Eccentricity Error of Gear Skiving Cutting Tool Movement on Gear Skiving Accuracy

Guo Wenchao; Yang Yu; Mao Shimin; Guo Zheng

doi:10.16578/j.issn.1004.2539.2020.07.015

您当前的位置：

首页 >

文章列表页 >

Analysis of the Influence of Eccentricity Error of Gear Skiving Cutting Tool Movement on Gear Skiving Accuracy

Test·Analysis | 更新时间：2022-10-20

- Analysis of the Influence of Eccentricity Error of Gear Skiving Cutting Tool Movement on Gear Skiving Accuracy
- Journal of Mechanical Transmission Vol. 44, Issue 7, Pages: 89-94(2020)
- 作者机构：
  
  1.西安交通大学机械工程学院，陕西西安 710049
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2020.07.015
  CLC：
扫描看全文
郭文超,杨羽,毛世民等.车齿刀具运动偏心误差对车齿精度的影响分析[J].机械传动,2020,44(07):89-94.

Guo Wenchao Yang Yu Mao Shimin Guo Zheng.Analysis of the Influence of Eccentricity Error of Gear Skiving Cutting Tool Movement on Gear Skiving Accuracy[J].Journal of Mechanical Transmission,2020,44(07):89-94.
郭文超,杨羽,毛世民等.车齿刀具运动偏心误差对车齿精度的影响分析[J].机械传动,2020,44(07):89-94. DOI： 10.16578/j.issn.1004.2539.2020.07.015.

Guo Wenchao Yang Yu Mao Shimin Guo Zheng.Analysis of the Influence of Eccentricity Error of Gear Skiving Cutting Tool Movement on Gear Skiving Accuracy[J].Journal of Mechanical Transmission,2020,44(07):89-94. DOI： 10.16578/j.issn.1004.2539.2020.07.015.

摘要

车齿刀具运动偏心误差对车齿精度的影响十分明显。通过理论及实验研究的方法，针对车齿过程中刀具运动偏心误差对车齿工件齿形、齿向及齿距误差的影响规律及作用机理展开研究。首先，对车齿工艺方法进行实验研究，针对车齿过程中常见的齿面波纹进行分析，并指出通过减小刀具运动偏心误差可明显改善工件齿面波纹度。然后，基于车齿实验研究，针对刀具运动偏心误差对工件齿向、齿形误差的影响进行理论分析，研究齿面波纹的产生机理及周期特性。最后，基于车齿理论与实验研究，提出可改善工件齿面波纹的车齿刀具齿数的设计方法。

Abstract

The skiving cutting tool movement eccentricity error has obvious influences on skiving gear accuracy. Based on the theoretical and experimental study of skiving，the influences of cutting tool eccentricity error on the helix deviations and the tooth profile deviations of the workpiece machined by skiving and action mechanism are investigated. Firstly，experiments of skiving process method are carried out，which are focused on the skiving waves on the tooth flanks of the workpieces，it is found that the amplitude of the waves can be decreased by reducing the tool eccentricity error. Then，based on the experiment study，the theoretical analysis of the influences of tool eccentricity error on the helix deviations and the tooth profile deviations of the workpiece are carried out，and the wave generation mechanisms and periodic characteristic are investigated. Finally，based on the experiments and theoretical study，the design method of number of tooth of skiving cutting tool，which can be used to improve the gear skiving waves on the tooth surface of the workpieces is proposed.

关键词

车齿刀具偏心齿形误差齿向误差

Keywords

SkivingCutting tool eccentricityTooth profile errorTooth helix error

references

SEIBICKE F，MÜLLER H.Good things need some time[J].Sigma,2011(20):6-13.

STADTTFELD H.Power skiving of cylindrical gears on different machine platforms[J].Gear Technology,2014，31（1）:52-62.

ARBOR A.Wera profilator introduces scudding process[J].Gear Technology,2008（11）:18-41.

KOBIALKA C.Contemporary gear pre-machining solutions[J].Gear Solutions，2013:43-49.

毛世民.车齿齿形分析[J].机械传动，2014，38（10）:50-53.

MAO Shimin.Analysis of the skiving gear profile[J].Journal of Mechanical Transmission，2014，38（10）:50-53.

GUO Z，MAO S M，LI X E.et al.Research on the theoretical tooth profile errors of gears machined by skiving[J].Mechanism and Machine Theory，2016（97）:1-11.

STURE SJOO.Tool and a cutting insert for power skiving:US 2015063927[P].2015-03-05.

MARX H，VOGEL O.Robust method for skiving and corresponding apparatus comprising a skiving tool:US 9120165[P].2015-09-01.

MARX H，VOGEL O.Semi-completing skiving method and device having corresponding skiving tool for executing a semi-completing skiving method:US 2013071197[P].2013-03-21.

GUO E，HONG R，X.HUANG X，et al.A novel power skiving method using the common shaper cutter[J].Internationa of Advancse Manufacturing，2015（83）:157-165.

GUO E，HONG R X,HUANG X，et al.A correction method for power skiving of cylindrical gears lead modification[J].Journal Mechanical Science and Technology，2015（29）:4379-4386.

陈新春，李佳，贺友平.直齿剐齿刀结构设计与计算[J].天津大学学报，2012，45（5）:411-416.

CHEN Xinchun，LI Jia，HE Youping.Structure design and calculation of spur slice cutter[J].Journal of Tianjin University，2012，45（5）:411-416.

李佳，陈新春，张鸿源.圆柱齿轮剐齿技术[J].机械工程学报，2011，47（19）:193-198.

LI Jia，CHEN Xinchun，ZHANG Hongyuan.Slicing thchnology of cylindrical gaers[J].Journal of Mechanical Engineering，2011，47（19）:193-198.

CHEN X C，LI J，ZOU Y，et al.A study on the grinding of the major flank face of error-free spur slice cutter[J].The International Journal of Advanced Manufacturing，2014（24）:425-438.

金精.车齿法原理与实验结果[J].西安交通大学学报，1962（2）:71-99.

JIN Jing.The principle and experimental results of gear skiving method[J].Journal of Xi'an Jiaotong University，1962（2）:71-99.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰