Flow Pulsation Characteristic of External Gear Pump and Analysis of Influencing Factor

Liangyi Shen; Lei Qu; Biao Shen

doi:10.16578/j.issn.1004.2539.2020.01.022

您当前的位置：

首页 >

文章列表页 >

Flow Pulsation Characteristic of External Gear Pump and Analysis of Influencing Factor

Test·Analysis | 更新时间：2022-11-10

- Flow Pulsation Characteristic of External Gear Pump and Analysis of Influencing Factor
- Journal of Mechanical Transmission Vol. 44, Issue 1, Pages: 132-136(2020)
- 作者机构：
  
  1.南通职业大学机械工程学院，江苏南通 226007
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2020.01.022
  CLC：
扫描看全文
沈良翼,瞿磊,申彪.外啮合齿轮式机油泵流量脉动特性及影响因素分析[J].机械传动,2020,44(01):132-136.

Shen Liangyi Qu Lei Shen Biao.Flow Pulsation Characteristic of External Gear Pump and Analysis of Influencing Factor[J].Journal of Mechanical Transmission,2020,44(01):132-136.
沈良翼,瞿磊,申彪.外啮合齿轮式机油泵流量脉动特性及影响因素分析[J].机械传动,2020,44(01):132-136. DOI： 10.16578/j.issn.1004.2539.2020.01.022.

Shen Liangyi Qu Lei Shen Biao.Flow Pulsation Characteristic of External Gear Pump and Analysis of Influencing Factor[J].Journal of Mechanical Transmission,2020,44(01):132-136. DOI： 10.16578/j.issn.1004.2539.2020.01.022.

摘要

采用机油泵台架试验，分析了泵出压力对外啮合齿轮式机油泵流量脉动特性的影响，结果表明，机油泵的流量脉动系数随泵出压力的增加而减小。运用理论推导和模拟相结合的方法，考察了机油泵的异齿数、模数、压力角及端面间隙等参数对流量脉动的影响。分析表明，模数对机油泵的流量脉动无影响，压力角、异齿数和端面间隙是影响机油泵流量脉动的主要因素；随压力角的增大，流量脉动系数呈逐渐减小趋势。主动轮与从动轮齿数的增加，都有利于减小流量脉动系数，改善机油泵的流量脉动现象，其中，主动轮齿数对流量脉动的影响较大。机油泵的流量脉动系数随端面间隙的增大而有所减小。

Abstract

Based on the bench test of oil pump， the influence of pump outlet pressure on flow pulsation of external gear oil pump is analyzed. The results show that the flow pulsation coefficient of the oil pump decreased with the increase of pump outlet pressure. The effects of different teeth number， modulus， pressure angle and end clearance on flow pulsation of oil pump are investigated by method of theoretical derivation and simulation. The analysis showed that the modulus had no effect on the flow pulsation of oil pump. The analysis shows that the pressure angle， the number of different teeth and the end clearance are the main factors affecting the flow pulsation. The flow pulsation coefficient decreased gradually with the increase of pressure angle. Increasing the number of driving gear teeth and driven gear teeth are beneficial to reducing the flow pulsation coefficient and improving the flow pulse phenomenon of oil pump. Among them， the number of driving gear teeth has a great influence on the flow pulsation. The flow pulsation coefficient of the oil pump decreased with the increase of the end clearance.

关键词

外啮合齿轮泵机油泵流量脉动柴油机

Keywords

External gear pumpOil pumpFlow pulsationDiesel engine

references

童宝宏，桂长林，陈华，等.发动机机油泵供油特性的神经网络建模[J].内燃机学报，2007，25(3):265-270.

TONG Baohong，GUI Changlin，CHEN Hua，et al.Neural network modeling for oil delivery performance of oil pump in engines[J].Transactions of CSICE，2007，25(3)：265-270.

阮桢，胡德金，许黎明，等.内燃机机油泵工作特性数学模型的分析与研究[J].内燃机工程，2006，27(3):50-53.

RUAN Zhen，HU Dejin，XU Liming，et al.Analysis and research on mathematical model of oil pump’s operating characteristic[J].Chinese Internal Combustion Engine Engineering，2006，27(3):50-53.

邹洪峰，贾柱.齿轮泵的流量脉动机理分析与设计[J].机械工程师，2010(3):47-48.

ZOU Hongfeng，JIA Zhu.Flow pulsation mechanism analysis and design of gear pump[J].Academic Communication，2010(3):47-48.

胡开文，徐金榜.齿轮泵工作原理的探讨[J].农业机械学报，2000，31(2):67-70.

HU Kaiwen，XU Jinbang.Discussion about working principle of a gear pump[J].Transactions of the Chinese Society of Agricultural Machinery，2000，31(2):67-70.

李玉龙，刘焜.异齿数对外啮合齿轮泵流量特性的影响[J].起重运输机械，2008(11):78-81.

LI Yulong，LIU Kun.Influence of different teeth number on flow characteristics of external meshing gear pump[J].Hoisting and Conveying Machinery，2008(11):78-81.

郜立焕，李言芝，唐晓阳.基于完全封闭解的外啮合齿轮泵运动学流动特性分析[J].液压与气动，2011(4):1-3.

GAO Lihuan，LI Yanzhi，TANG Xiaoyang.Analysis of external gear pumps kinematic flow characteristics with exact closed solution[J].Chinese Hydraulics & Pneumatics，2011(4):1-3.

NOAH D M，SURESH B K.The theoretical flow ripple of an external gear pump[J].Journal of Dynamic Systems Measurement and Control，2003，125(3):396-404.

孔繁余，何玉洋，郑德，等.外啮合齿轮泵流量特性影响因素分析[J].排灌机械工程学报，2014，32(2):108-112.

KONG Fanyu，HE Yuyang，ZHENG De，et al.Analysis of influence factors on flow rate characteristics in gear pump[J].Journal of Drainage and Irrigation Machinery Engineering，2014，32(2):108-112.

周兰美.外啮合齿轮泵变位系数对流量脉动的影响[J].煤矿机械，2011，32(1):110-111.

ZHOU Lanmei.Influence of modification coefficient of flow pulsation of external gear pump[J].Coal Mine Machinery，2011，32(1):110-111.

臧克江，陈鹰.AutoCAD环境下的齿轮泵理论流量计算与验证[J].农业机械学报，2003，34(5):76-79.

ZANG Kejiang，CHEN Ying.Calculation of gear pump flow rate based on autocad and experimental verification[J].Transactions of the Chinese Society of Agricultural Machinery，2003，34(5):76-79.

CAMPO D D，CASTILLA R，RAUSH GA，et al.Numerical analysis of external gear pumps including cavitation[J].Journal of Fluids Engineering，2012，134(8):1-12.

曾德堂，赵威力，王曦.基于向量机回归理论研究齿轮泵流量特性[J].机床与液压，2012，40(9):38-41.

ZENG Detang，ZHAO Weili，WANG Xi.Study on flow characteristic of gear pump based on support vector machines regression[J].Machine Tool & Hydraulics，2012，40(9):38-41.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰