Theoretical Analysis and Experimental Research of Spindle Swing Compound Barrel Finishing

Ding Xiongxiong; Zhang Yan; Li Wenhui; Li Xiuhong

doi:10.16578/j.issn.1004.2539.2019.12.028

您当前的位置：

首页 >

文章列表页 >

Theoretical Analysis and Experimental Research of Spindle Swing Compound Barrel Finishing

Development·Application | 更新时间：2022-10-25

- Theoretical Analysis and Experimental Research of Spindle Swing Compound Barrel Finishing
- Journal of Mechanical Transmission Vol. 43, Issue 12, Pages: 155-160(2019)
- 作者机构：
  
  1.太原理工大学机械工程学院，山西太原 030024
  2.精密加工山西省重点实验室，山西太原 030024
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2019.12.028
  CLC：
扫描看全文
丁熊熊,张演,李文辉等.主轴摆动复合滚磨光整加工齿轮理论分析及实验研究[J].机械传动,2019,43(12):155-160.

Ding Xiongxiong,Zhang Yan,Li Wenhui,et al.Theoretical Analysis and Experimental Research of Spindle Swing Compound Barrel Finishing[J].Journal of Mechanical Transmission,2019,43(12):155-160.
丁熊熊,张演,李文辉等.主轴摆动复合滚磨光整加工齿轮理论分析及实验研究[J].机械传动,2019,43(12):155-160. DOI： 10.16578/j.issn.1004.2539.2019.12.028.

Ding Xiongxiong,Zhang Yan,Li Wenhui,et al.Theoretical Analysis and Experimental Research of Spindle Swing Compound Barrel Finishing[J].Journal of Mechanical Transmission,2019,43(12):155-160. DOI： 10.16578/j.issn.1004.2539.2019.12.028.

摘要

提出了一种主轴摆动复合滚磨光整加工齿轮的新方法。建立切削速度与切削角的计算模型，利用Matlab软件分析各参数对切削速度和切削角的影响，理论验证了主轴摆动复合滚磨光整加工的可行性。开发了参数可调的实验装置，加工实验表明，齿面表面粗糙度,R,a,从0.8 μm左右降到0.3 μm左右，表面刀痕去除且表面纹理一致。结果表明，该方法能够有效地提高齿轮的表面质量，使得齿轮获得均匀性表面。

Abstract

A spindle swing compound barrel finishing equipment for gear machining is proposed. The calculation model of cutting speed and cutting angle is established. The influence of various parameters on cutting speed and cutting angle is analyzed by using Matlab software. The rationality of the design of spindle swing compound barrel finishing equipment is theoretically verified. An experimental device with adjustable parameters is developed. Machining experiments shows that the surface roughness Ra decreased from about 0.8 μm to about 0.3 μm. The cutting trace is removed and the surface texture is the same. The result shows that the equipment can effectively improve the surface quality of gears and obtain the uniform surface of gears.

关键词

齿轮滚磨光整加工切削速度切削角表面粗糙度

Keywords

GearBarrel finishingCutting speedCutting angleSurface roughness

references

周长江，汪红兵，雷玉英，等.齿轮磨损计算与测试方法及抑制技术[J].北京工业大学学报，2018，44（7）:987-1000.

别文博，赵波，王晓博，等.超声加工在齿轮抗疲劳制造中的研究综述与展望[J].表面技术，2018，47（7）:35-51.

DING H.Dynamic wear models for gear systems[D].Ohio:The Ohio State University，2007:10-11.

ATANASIU V，OPRISAN C，LEOHCHI D.The effect of tooth wear on the dynamic transmission error of helical gears with smaller number of pinion teeth[J].Applied Mechanics & Materials，2014，657:649-653.

王晓明，周锦进.电化学机械加工对汽车齿轮使用性能和寿命的影响[J].汽车工程，2013（z1）:49-53.

李洪友，周锦进，庞桂兵，等.表面质量对齿轮使用性能指标的影响[J].农业机械学报，2004，35（4）:174-178.

周愿愿.齿轮化学机械光整加工技术研究[D].大连：大连理工大学，2010:4-5.

尹夕兵，章峰.一种滚齿齿向非对称修形的方法[J].安徽科技，2015（4）:53.

郑喜朝.硬齿面齿轮精加工技术的现状与展望[J].新技术新工艺，2013（4）:88-90.

杨波.高精度齿轮的加工工艺分析[J].机械工人（冷加工），2007（6）:30-31.

雷洪，李秀红，李文辉，等.垂直主轴式齿轮滚磨光整加工方法的研究[J].机械设计与制造，2018（12）:207-209.

聂勇.垂直交叉主轴式滚磨光整加工改善齿根处表面质量的实验研究[J].机械传动，2018，42（5）:139-142.

杨胜强，李文辉，陈红玲，等.表面光整加工理论与新技术[M].北京：国防工业出版社，2011:87-88.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰