Design and Simulation Analysis of a New Frictionless Synchronizer

Chen Yongzhong; Zhu Bo; Zhang Nong

doi:10.16578/j.issn.1004.2539.2019.11.007

您当前的位置：

首页 >

文章列表页 >

Design and Simulation Analysis of a New Frictionless Synchronizer

更新时间：2022-10-25

- Design and Simulation Analysis of a New Frictionless Synchronizer
- Journal of Mechanical Transmission Issue 11, Pages: 39-46(2019)
- 作者机构：
  
  1.合肥工业大学汽车与交通工程学院，安徽合肥 230009
  2.合肥工业大学汽车工程技术研究院，安徽合肥 230009
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2019.11.007
  CLC：
扫描看全文
陈永忠,朱波,张农.一种新型无摩擦式同步器设计及仿真分析[J].机械传动,XXXX,XX(XX):39-46.

Chen Yongzhong,Zhu Bo,Zhang Nong.Design and Simulation Analysis of a New Frictionless Synchronizer[J].Journal of Mechanical Transmission,XXXX,XX(XX):39-46.
陈永忠,朱波,张农.一种新型无摩擦式同步器设计及仿真分析[J].机械传动,XXXX,XX(XX):39-46. DOI： 10.16578/j.issn.1004.2539.2019.11.007.

Chen Yongzhong,Zhu Bo,Zhang Nong.Design and Simulation Analysis of a New Frictionless Synchronizer[J].Journal of Mechanical Transmission,XXXX,XX(XX):39-46. DOI： 10.16578/j.issn.1004.2539.2019.11.007.

摘要

设计了一款新型无摩擦式同步器，运用三维软件CATIA建立三维实体模型，并将实体模型导入Adams中，建立新型无摩擦式同步器的虚拟样机模型；同时，在Matlab/Simulink中建立一两挡纯电动汽车整车模型，利用Adams和Simulink进行联合仿真，模拟新型无摩擦式同步器的速度同步及退挡过程。仿真结果表明，相比于依靠摩擦实现速度同步的传统同步器，新型同步器在汽车挂挡速度同步及退挡过程中产生的冲击度得到减小，且所需的速度同步及退挡时间也大幅降低，减少了汽车换挡过程中的动力中断及换挡顿挫感。最后，分析了换挡速度同步过程中的车速、螺旋弹簧刚度值以及换挡力大小等参数对新型同步器速度同步过程的影响。

Abstract

A new type of frictionless synchronizer is designed，and its three-dimensional model is built by using the software CATIA. The three-dimensional model is imported into Adams to establish a virtual prototype model and a two-gear pure electric vehicle model is built in Matlab/Simulink which is used to simulate the speed synchronization and backing process of the new synchronizer. The simulation results show that the jerk produced by the new type of synchronizer in the speed synchronization and backing process is reduced and the required time of speed synchronization and backing is also greatly reduced，which reduce the power interruption and shift frustration in the process of automobile shift，comparing with the traditional synchronizer which relies on friction to achieve speed synchronization. Finally，the influence of vehicle speed in synchronization process, helical spring stiffness and shift force for the synchronization process of frictionless synchronizer is analyzed.

关键词

同步器设计虚拟样机模型同步过程仿真分析影响因素分析

Keywords

Design of synchronizerVirtual prototype modelSynchronization processSimulation analysisAnalysis of influencing factor

references

陈访.虚拟样机技术在汽车变速器中的应用[D].合肥:合肥工业大学，2007:25-36.

CHANGENET C，OVIEDO-MARLOT X，VELEX P .Power loss predictions in geared transmissions using thermal networks-application to a six speed manual gearbox[J].Journal of Mechanical Design，2005，128（3）:618-625.

TSENG C Y，YU C H.Advanced shifting control of synchronizer mechanisms for clutchless automatic manual transmission in an electric vehicle[J].Mechanism and Machine Theory，2015，84:37-56.

LIU H，LEI Y，LI Z，et al.Gear-shift strategy for a clutchless automated manual transmission in battery electric vehicles[J].SAE International Journal of Commercial Vehicles，2012，5（1）:57-62.

SORNIOTTI A，HOLDSTOCK T，EVERITT M，et al.A novel clutchless multiple-speed transmission for electric axles[J].Powertrains，2013，2（2/3）:103-131.

ZHAO K G.Uninterrupted shift transmission and its shift characteristics[J].IEEE/ASME Transctions on Mechatronics，2014，19（1）:374-383.

ZHOU X，WALKER P D，ZHANG N，et al.Numerical and experimental investigation of drag torque in a two-speed dual clutch transmission[J].Mechanism and Machine Theory，2014，79:46-63

WALKER P D，RAHMAN S A，ZHU B，et al.Modelling，simulations，and optimisation of electric vehicles for analysis of transmission ratio selection[J].Advances in Mechanical Engineering，2013，5:1-13.

周帅.汽车手动变速器同步器的建模与仿真研究[D].武汉:武汉理工大学，2011:29-48.

MO W W，WALKER P D，FANG Y H，et al.A novel shift control concept for multi-speed electric vehicles[J].Mechanical Systems and Signal Processing，2018，112:171-193.

陈玉祥.基于虚拟样机技术的机械式变速器换挡性能仿真分析[D].广州：华南理工大学，2012:39-52.

陈震，钟再敏，章桐.基于ADAMS的同步器同步过程仿真分析[J].汽车工程，2011，33（4）:340-344.

傅友宾.基于PRO/E和ADAMS的变速器动力学仿真[D].大连: 大连理工大学，2007:10-36.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰