Selection Analysis of Drive Chain Drive System of Diesel Engine Matching Valve Mechanism based on FEV Software

Shukun Wang; Yefeng Xu; Debing Yin; Xudong Zhao

doi:10.16578/j.issn.1004.2539.2019.08.030

您当前的位置：

首页 >

文章列表页 >

Selection Analysis of Drive Chain Drive System of Diesel Engine Matching Valve Mechanism based on FEV Software

Development·Application | 更新时间：2022-09-25

- Selection Analysis of Drive Chain Drive System of Diesel Engine Matching Valve Mechanism based on FEV Software
- Journal of Mechanical Transmission Vol. 43, Issue 8, Pages: 162-165(2019)
- 作者机构：
  
  1.长春理工大学机电工程学院，吉林长春 130022
  2.湖州求精汽车链传动有限公司，浙江湖州 313012
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2019.08.030
  CLC：
扫描看全文
王淑坤,徐业锋,尹德兵等.基于FEV软件柴油发动机配气机构驱动链传动系统选型分析[J].机械传动,2019,43(08):162-165.

Wang Shukun,Xu Yefeng,Yin Debing,et al.Selection Analysis of Drive Chain Drive System of Diesel Engine Matching Valve Mechanism based on FEV Software[J].Journal of Mechanical Transmission,2019,43(08):162-165.
王淑坤,徐业锋,尹德兵等.基于FEV软件柴油发动机配气机构驱动链传动系统选型分析[J].机械传动,2019,43(08):162-165. DOI： 10.16578/j.issn.1004.2539.2019.08.030.

Wang Shukun,Xu Yefeng,Yin Debing,et al.Selection Analysis of Drive Chain Drive System of Diesel Engine Matching Valve Mechanism based on FEV Software[J].Journal of Mechanical Transmission,2019,43(08):162-165. DOI： 10.16578/j.issn.1004.2539.2019.08.030.

摘要

配气机构驱动链传动系统是用以驱动发动机的配气机构，使发动机进排气门适时开闭，其选型结果直接影响发动机动力性能。在给定某款柴油发动机相关参数的基础上，首先，由理论计算得出链条所承受的最大工作张力，完成链条初选；然后，在FEV软件中建立相匹配的配气机构驱动链传动系统，输入仿真前期所需参数，通过仿真获取链条最大工作张力，再通过二者比较来完成链条终选。研究结果表明，这种链条的选型方法是可行的，并已经成功应用在链条生产企业配套选型中。

Abstract

The matching valve mechanism drive chain drive system is used to drive the matching valve mechanism of the engine, so that the engine intake and exhaust valves timely open and close, its selection results directly affecting the engine dynamic performance. The maximum working tension of a diesel engine chain is calculated theoretically on the basis of giving the relevant parameters of a diesel engine, and the primary selection of the chain is completed. Then, a matching valve mechanism driving chain transmission system is established in FEV software to input the required parameters in the early stage of simulation, and the maximum working tension of the chain is obtained through simulation. Then finish the chain final selection through the comparison of the two. The research results show that the selection method of the chain is reliable, it has been successfully applied in the selection of chain production enterprises.

关键词

链条选型FEV软件仿真链条张力

Keywords

Chain selectionFEV softwareSimulationChain tension

references

蒋俊美.TPS驱动的常州链条制造业供应链网式优化［D］.桂林：桂林理工大学，2013：1-2.

奚佳欣.柴油发动机正时链系统噪声源识别及振动噪声特性研究［D］.长春：吉林大学，2015：4-5.

金玉谟，付振明.链传动在汽车发动机上的应用［J］.机械传动，2012，36（1）：6-8.

孟繁忠，李宝林，吕翔，等.汽车发动机正时链系统设计方法［J］.哈尔滨工业大学学报，2009：121-124.

王志利.柴油机喷油泵技术状态检查［J］.农机使用与维修，2013，11：87-88.

尹德兵，翁建良，钱江，等.发动机正时链系统设计方法［J］.机械传动，2016（11）：40-44.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Kinematics Modeling and Simulation of a Self-propelled Wrapping Packaging Robot

Analysis of the Influence of the Parameters of the Pendulum Mechanism of the Swashplate Engine on the Dynamic Performance

Design and Analysis of Upper Limb Rehabilitation Robots with Fully-actuated Shoulder Joints

The Design and Simulation of a Quadruped Multi-mode Mobile Robot

Gait Analysis and Simulation of a Multi-mode 4-UPU Mechanism

Related Author

No data

Related Institution

Zhengzhou Key Laboratory of Intelligent Assembly Manufacturing and Logistics Optimization, Zhengzhou College of Finance and;Economics

Mechanical and Electrical Engineering Institute, Zhengzhou University of Light Industry

College of Innovation and Entrepreneurship, Henan Open University

School of Mechantronics & Vehicle Engineering, Chongqing Jiaotong University

The Green Aerotechnics Research Institute of Chongqing Jiaotong University

⁰