Deviation Analysis of Processed Tooth Profile with Plated CBN Hard Gear Honing

Yun Yan; Mandong Zhang

doi:10.16578/j.issn.1004.2539.2019.04.029

您当前的位置：

首页 >

文章列表页 >

Deviation Analysis of Processed Tooth Profile with Plated CBN Hard Gear Honing

Development·Application | 更新时间：2022-10-03

- Deviation Analysis of Processed Tooth Profile with Plated CBN Hard Gear Honing
- Journal of Mechanical Transmission Vol. 43, Issue 4, Pages: 157-160(2019)
- 作者机构：
  
  1.山西水利职业技术学院机电工程系，山西太原 030024
  2.太原理工大学机械工程学院，山西太原 030024
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2019.04.029
  CLC：
扫描看全文
燕芸,张满栋.电镀CBN硬珩齿齿廓偏差分析[J].机械传动,2019,43(04):157-160.

Yan Yun,Zhang Mandong.Deviation Analysis of Processed Tooth Profile with Plated CBN Hard Gear Honing[J].Journal of Mechanical Transmission,2019,43(04):157-160.
燕芸,张满栋.电镀CBN硬珩齿齿廓偏差分析[J].机械传动,2019,43(04):157-160. DOI： 10.16578/j.issn.1004.2539.2019.04.029.

Yan Yun,Zhang Mandong.Deviation Analysis of Processed Tooth Profile with Plated CBN Hard Gear Honing[J].Journal of Mechanical Transmission,2019,43(04):157-160. DOI： 10.16578/j.issn.1004.2539.2019.04.029.

摘要

用标准渐开线电镀CBN硬珩轮加工齿轮后，一般情况下在工件齿廓节点附近会产生 “中凹”误差。利用Pro/E软件对珩轮和被珩齿轮进行了三维参数化实体建模，并对它们进行了精确的啮合装配，再利用ANSYS软件进行珩齿接触分析，通过对齿面接触应力和被加工齿面法向变形量的分析，找到齿廓偏差的影响因素。然后，在其他参数不变的前提下，分别变换被珩齿轮的齿数，对比接触应力的变化情况，进而找出被珩齿轮齿数对“中凹”误差的影响趋势。

Abstract

Plating CBN hard gear honing processing gear with standard involute， the general vicinity of the workpiece tooth pitch will be a “mid concave” error. The Pro/E software is used to establish three-dimensional parameterization entity model of gear-honing-tools and gears， and build meshing assemble between them accurately. ANSYS software is used to simulate the contact analysis of plating CBN hard honing process. Through the analysis of the contact stress of the tooth surface and the normal deformation of the processed tooth surface， the influence factors on the concave error are found out. Then，under the premise of other parameters are fixed， the tooth numbers of gears is changed respectively， comparing the change of contact stress， and then the influence of the teeth numbers to on “mid concave” error is found out.

关键词

硬珩齿加工参数化建模齿面接触分析齿廓偏差

Keywords

Hard gear honingParametric modelingTooth contact analysisTooth profile deviation

references

王长路，李秀明，刘毅. CBN整形外珩轮研究［J］. 机械传动，2002， 26（2）：67-70.

胡震. 剃齿刀齿面修形造型研究［D］. 太原：太原理工大学， 2006：25-40．

熊晨曦，张满栋. 基于ANSYS的齿轮珩磨过程中接触应力及接触轨迹分析［J］. 机械管理开发， 2009， 24（4）：188-189．

王长路，刘毅，陈立. CBN珩轮整形珩齿机理研究［J］. 机械传动， 2002， 26（3）：20-23．

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Deviation Evaluation Method of Cylindrical Gear Tooth Surface Based on the Coordinates of the Actual Tooth Surface Points

Analysis and Approximate Replacement of Tool for Trapezoid Spline Shaft

Numerical Compensation Method for Measuring Error of Tooth Profile of ZC1 Worm on Shaft Section

Optimization of Contact Path and Transmission Error based on Installation and Adjustment of Spiral Bevel Gear

Study on Tooth Profile Parameter of Gear Skiving Under the Influence of Multiple Factor

Related Author

No data

Related Institution

Department of International Cooperation & Exchanges, Henan University of Science and Technology

Student Affair Office, Henan University of Science and Technology

School of Mechatronics Engineering, Henan University of Science and Technology

Zhengzhou Research Institute of Mechanical Engineering Co.， Ltd.

Beijing Engineering Research Center of Precision Measurement Technology and Instruments，Faculty of Materials and Manufacturing，Beijing University of Technology

⁰