Life Analysis of Standard Planetary Roller Screw Mechanism based on Structural Parameter

Fu Yongling; Zheng Shicheng; Gan Fajin

doi:10.16578/j.issn.1004.2539.2018.11.022

您当前的位置：

首页 >

文章列表页 >

Life Analysis of Standard Planetary Roller Screw Mechanism based on Structural Parameter

更新时间：2022-10-20

- Life Analysis of Standard Planetary Roller Screw Mechanism based on Structural Parameter
- Vol. 42, Issue 11, Pages: 117-122(2018)
- 作者机构：
  
  1. 北京航空航天大学机械工程及自动化学院
  2. 中国航天空气动力技术研究院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.11.022
  CLC：
扫描看全文
[1]付永领,郑世成,甘发金.基于结构参数的标准式行星滚柱丝杠副寿命分析[J].机械传动,2018,42(11):117-122.

Fu Yongling, Zheng Shicheng, Gan Fajin. Life Analysis of Standard Planetary Roller Screw Mechanism based on Structural Parameter. [J]. 42(11):117-122(2018)
[1]付永领,郑世成,甘发金.基于结构参数的标准式行星滚柱丝杠副寿命分析[J].机械传动,2018,42(11):117-122. DOI： 10.16578/j.issn.1004.2539.2018.11.022.

Fu Yongling, Zheng Shicheng, Gan Fajin. Life Analysis of Standard Planetary Roller Screw Mechanism based on Structural Parameter. [J]. 42(11):117-122(2018) DOI： 10.16578/j.issn.1004.2539.2018.11.022.

摘要

以用于飞机机电作动器的标准式行星滚柱丝杠副为研究对象,针对其寿命分别利用力学理论进行计算获得解析解、利用ANSYS Workbench软件进行有限元仿真分析,并将解析解与仿真结果进行对比,两者的偏差值最大不超过5%。在此基础上,分析了丝杠导程（螺纹升角）对丝杠副寿命的影响,结果表明,随着丝杠导程（螺纹升角）增大,丝杠副寿命逐渐增大,说明适当增大丝杠导程（螺纹升角）,可以提高丝杠副的寿命。同时分析了滚柱根数对丝杠副寿命的影响,随着滚柱根数的增多,接触点个数随之增加,丝杠副寿命逐渐变大,从增大丝杠副寿命的角度来看,滚柱根数越多越好。研究为研制高可靠性长寿命的行星滚柱丝杠副提供了优化设计和分析的依据。

Abstract

Taking the standard planetary roller screw mechanism for aircraft electro mechanical actuator as the research object,the analytical solution is obtained by calculating the mechanical properties of the fiber,using ANSYS Workbench software for finite element simulation analysis,and the analytical solution is compared with the simulation results,the maximum deviation value of the two is not more than 5%. On this basis,the influence of lead of screw （lead angle） on screw life is analyzed. The results show that with the increase of lead of screw （lead angle）,the life of screw pair gradually increases. It shows that proper increase lead of screw （lead angle）,can improve the life of screw pair. At the same time,the influence of roller root number on the life of screw pair is analyzed. With the increase of roller root number,total contact points increased,and the life of the screw pair will gradually increase. From the point of increasing the life of the screw pair,the more of roller root number is,the better. This research provides the basis for the optimization design and analysis of the planetary roller screw mechanism with high reliability and long life.

关键词

标准式行星滚柱丝杠副寿命丝杠导程螺纹升角滚柱根数

Keywords

Standard planetary roller screw mechanismLifeLead of screwLead angleRoller number

references

Views

159

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical Optimization Method and Experimental Verification of Contact Strength of U-Joint Bearings

Exploring the Influence of Different Lubricant Viscosity on the Fatigue Life of Gear

Grey Prediction for Accuracy Life of Roller Pushing Mechanism

Development of Cam-tappet Life Prediction Simulation System based on the Friction Work Principle

Related Author

No data

Related Institution

Wanxiang Qianchao Co., Ltd.

Gear Research Institute,Taiyuan University of Science and Technology

School of Mechanical Engineering,Nantong Vocational University

School of Traffic and Transportation Engineering,Central South University

Mechanical Engineering Department,Hunan Industry Polytechnic

⁰