Analysis of Elastohydrodynamic Lubrication Performance for TI Hourglass Worm Drive with Considering Tribo-dynamics Character

Zhu Yan; Liu Zaixin; Liao Honghui; Zhang Cui

doi:10.16578/j.issn.1004.2539.2018.09.022

您当前的位置：

首页 >

文章列表页 >

Analysis of Elastohydrodynamic Lubrication Performance for TI Hourglass Worm Drive with Considering Tribo-dynamics Character

更新时间：2022-10-20

- Analysis of Elastohydrodynamic Lubrication Performance for TI Hourglass Worm Drive with Considering Tribo-dynamics Character
- Vol. 42, Issue 9, Pages: 111-117(2018)
- 作者机构：
  
  1. 西华大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.09.022
  CLC：
扫描看全文
[1]朱焱,柳在鑫,廖鸿辉,张翠.考虑摩擦动力学特性的TI环面蜗杆传动弹流润滑分析[J].机械传动,2018,42(09):111-117.

Zhu Yan, Liu Zaixin, Liao Honghui, et al. Analysis of Elastohydrodynamic Lubrication Performance for TI Hourglass Worm Drive with Considering Tribo-dynamics Character. [J]. 42(9):111-117(2018)
[1]朱焱,柳在鑫,廖鸿辉,张翠.考虑摩擦动力学特性的TI环面蜗杆传动弹流润滑分析[J].机械传动,2018,42(09):111-117. DOI： 10.16578/j.issn.1004.2539.2018.09.022.

Zhu Yan, Liu Zaixin, Liao Honghui, et al. Analysis of Elastohydrodynamic Lubrication Performance for TI Hourglass Worm Drive with Considering Tribo-dynamics Character. [J]. 42(9):111-117(2018) DOI： 10.16578/j.issn.1004.2539.2018.09.022.

摘要

综合考虑时变啮合刚度、传递误差和粗糙峰摩擦因数的影响,基于载荷分担理论和动力学理论建立了TI环面蜗杆传动副简易动力学模型,将摩擦动力学特性考虑到线接触弹流润滑理论（EHL）中,求解获得啮合周期内轮齿的啮合力与摩擦力变化趋势,绘制了不同参数下油膜压力和油膜厚度的分布情况。计算结果表明,低速时,啮入端的轮齿啮合力和摩擦力均大于高速时的啮合力和摩擦力;螺旋角增大,啮入端和啮出端的轮齿啮合力都明显增大;轮齿摩擦力随转速变化较小。最大摩擦力值降低,可提高蜗轮副传动寿命;轮齿啮合刚度对油膜压力和油膜厚度的影响最大,轮齿啮合力和粗糙峰摩擦因数影响较小。

Abstract

The simple tribo-dynamics model for TI hourglass worm drive is proposed based on the load sharing theory and dynamic theory,which took the time-varying mesh stiffness,transmission error and friction coefficient of rough peak into account. The tribo-dynamics character is considered into line contact Elastohydrodynamic Lubrication（ EHL）. The meshing force and friction changes,oil film pressure and thickness distribution are obtained by calculation. The calculation results show that,when at low speed,the meshing force and friction of the tooth are larger than those at high speed. With the increase of the helix angle,the meshing forces both at inlet and outlet are obviously improved,and the friction of the tooth changes a little with the speed.Meanwhile,the maximum friction reduces,which can improve the transmission life of the worm drive pair. The meshing stiffness of the tooth has the greatest impact on oil film pressure and thickness,and the meshing force and friction coefficient of rough peak have less influence correspondingly.

关键词

TI环面蜗杆摩擦动力学弹流润滑油膜压力油膜厚度

Keywords

TI hourglass worm driveTribo-dynamicsElastohydrodynamic lubricationOil film pressureOil film thickness

references

Views

118

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influence of Roughness on Isothermal Elastohydrodynamic Lubrication of Roller Enveloped Worm Drive

Analysis of Elastohydrodynamic Lubrication Characteristic of the Roller Enveloping Hourglass Worm Drive

Analysis and Establishment of the Isothermal Elastohydrodynamic Lubrication Model of the Cylindrical Gear with Arcuate Tooth Trace

Thermal Elastohydrodynamic Lubrication Analysis of Bevel Gear based on a Finite Line Contact Model

Effects of Profile Modification on Elastohydrodynamic Lubrication of Straight Bevel Gear

Related Author

No data

Related Institution

School of Mechanical Engineering， Xihua University

School of Intelligent Engineering， College of Mobile Telecommunications Chongqing University of Posts and Telecommunications

School of Manufacturing Science and Engineering,Sichuan University

School of Mechanical and Automotive Engineering，Qingdao University of Technology

Three Gorges Navigation Authority

⁰