Static Stiffness Analysis of a New Scissor-type Telescoping and Lifting Mechanism

Hao Gang; Chang Boyan; Li Wenqi

doi:10.16578/j.issn.1004.2539.2018.09.020

您当前的位置：

首页 >

文章列表页 >

Static Stiffness Analysis of a New Scissor-type Telescoping and Lifting Mechanism

更新时间：2022-10-20

- Static Stiffness Analysis of a New Scissor-type Telescoping and Lifting Mechanism
- Vol. 42, Issue 9, Pages: 102-105(2018)
- 作者机构：
  
  1. 天津工业大学机械工程学院
  2. 石家庄职业技术学院机电工程系
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.09.020
  CLC：
扫描看全文
[1]郝刚,畅博彦,李文启.新型剪叉式可伸缩可升降机构及其静刚度分析[J].机械传动,2018,42(09):102-105.

Hao Gang, Chang Boyan, Li Wenqi. Static Stiffness Analysis of a New Scissor-type Telescoping and Lifting Mechanism. [J]. 42(9):102-105(2018)
[1]郝刚,畅博彦,李文启.新型剪叉式可伸缩可升降机构及其静刚度分析[J].机械传动,2018,42(09):102-105. DOI： 10.16578/j.issn.1004.2539.2018.09.020.

Hao Gang, Chang Boyan, Li Wenqi. Static Stiffness Analysis of a New Scissor-type Telescoping and Lifting Mechanism. [J]. 42(9):102-105(2018) DOI： 10.16578/j.issn.1004.2539.2018.09.020.

摘要

将Hart直线机构和剪叉机构相结合,提出一种仅含转动副的直线可展单元结构模型,并以此为基础设计得到一种新型剪叉式可伸缩可升降机构,该机构可实现一维方向上的直线伸缩或升降运动。首先,阐述剪叉式可伸缩可升降机构的模块化组成原理,将机构的组成等效为底部模块、中部模块和顶部模块的顺序叠加,3种模块均由直线可展单元构成;其次,建立单个直线可展单元的运动学模型,结合机构的模块化组成原理,推导出任意模块间的运动学递推关系,并以此为基础构建多层模块条件下剪叉式可伸缩可升降机构的整体运动学模型,用以验证该型机构实现精确直线运动的正确性和有效性;最后,以3层2列剪叉式可伸缩可升降机构为例,对其进行静刚度虚拟仿真分析。结果表明,机构沿可伸缩方向具有较好的抵抗变形的能力。

Abstract

Combining hart straight-line mechanism with scissors mechanism,a new type of deployable model in straight-line motion which consists of revolute joint only is proposed. Corresponding modular system named scissor-type telescoping and lifting mechanism（ STLM） is designed for achieving straight-line motion in one dimension. Firstly,modular principle of STLM is explained and the composition of the mechanism is equivalent to the sequential stacking of three kinds of modules including bottom module,middle module and top module. These modules are all composed by the deployable model. Secondly,the kinematics equations of single deployable model is established and introduced into constructing the whole kinematics equations with multi-layer modules which can be used to validate the proposed method for achieving straight-line motion. Finally,taking STLM consisted with three-layer and two-row modules as an example,the structural behavior of static stiffness for this mechanism is analyzed by simulation. Results show a good performance in the stiffness along the deployable direction.

关键词

直线机构剪叉机构可展模块静刚度

Keywords

Straight line mechanismScissors mechanismDeployable moduleStatic stiffness

references

Views

388

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Statics Analysis of a New Type of Probe with Parallel Compliant Constraint

Study on the Static Stiffness of the Flexible Composite Connecting Rod

Study on the Static Stiffness of Large Diaphragm- rubber Coupling

Design and Characteristic Research of the Spindle Box of Vertical Machining Center

Related Author

No data

Related Institution

Huainan New Energy Research Center,Chinese Academy of Sciences

School of Mechanical Engineering,Anhui University of Science and Technology

School of Electrical and Information Engineering,Anhui University of Science and Technology

CSIC No. Research Institute

School of Mechanical Engineering,University of Shanghai for Science and Technology

⁰