Mechanism Research and Experiment of Two-dimensional Gearbox with Output Shaft Rotating and Reciprocating Motion

Wu Shangsheng; Deng Haiyan; Deng Hongjian; Liu Yaping

doi:10.16578/j.issn.1004.2539.2018.03.032

您当前的位置：

首页 >

文章列表页 >

Mechanism Research and Experiment of Two-dimensional Gearbox with Output Shaft Rotating and Reciprocating Motion

更新时间：2022-10-20

- Mechanism Research and Experiment of Two-dimensional Gearbox with Output Shaft Rotating and Reciprocating Motion
- Vol. 42, Issue 3, Pages: 155-159(2018)
- 作者机构：
  
  1. 华南理工大学机械与汽车工程学院
  2. 广东精创机械制造有限公司
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.03.032
  CLC：
扫描看全文
[1]吴上生,邓海燕,邓宏健,刘亚平.输出轴转动并往复运动的二维变速箱机理研究及试验[J].机械传动,2018,42(03):155-159.

Wu Shangsheng, Deng Haiyan, Deng Hongjian, et al. Mechanism Research and Experiment of Two-dimensional Gearbox with Output Shaft Rotating and Reciprocating Motion. [J]. 42(3):155-159(2018)
[1]吴上生,邓海燕,邓宏健,刘亚平.输出轴转动并往复运动的二维变速箱机理研究及试验[J].机械传动,2018,42(03):155-159. DOI： 10.16578/j.issn.1004.2539.2018.03.032.

Wu Shangsheng, Deng Haiyan, Deng Hongjian, et al. Mechanism Research and Experiment of Two-dimensional Gearbox with Output Shaft Rotating and Reciprocating Motion. [J]. 42(3):155-159(2018) DOI： 10.16578/j.issn.1004.2539.2018.03.032.

摘要

研究提出一种输出轴转动并往复运动的新型二维变速箱及传动原理,利用三维造型设计软件Inventor构建二维变速箱物理模型;采用双偏心机构幅值调整方法和偏心轮结构特点,设计往复运动相关部件,重点研究输出轴转动并轴向往复运动的机构工作原理。将二维变速箱物理模型导入Adams中,对其进行运动学分析,得出轴向往复运动部件的运动输出特性;在此基础上试制二维变速箱样机,样机装配在单螺杆挤出机上进行塑料挤出试验,验证了输出轴转动并往复运动的二维变速箱的合理性和可行性。

Abstract

A new type two-dimensional gearbox with the output of rotating and reciprocating motion and transmission principle are proposed. The physical model of the two-dimensional gearbox is constructed by using the three-dimensional modeling software Inventor. The reciprocating motion related assembly is designed by applying the method of double eccentricity amplitude adjustment and eccentric wheel structure characteristics,the working principle of the output shaft rotation and axial reciprocating motion mechanism is mainly studied. The kinematics analysis of the model is carried out in software ADAMS and the output characteristics of the axially reciprocating assembly motion are obtained. Based on the theory above,the prototype of the two-dimensional gearbox is developed and manufactured. The plastic extrusion experiment is carried out by mounting the prototype on a single screw extruder. The rationality and feasibility of the two-dimensional gearbox with the output shaft rotation and reciprocating motion are verified.

关键词

二维变速箱输出轴螺杆挤出机轴向往复运动仿真

Keywords

Two-dimensional gearboxOutput shaftScrew extruderAxial reciprocating motionSimulation

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Kinematics Modeling and Simulation of a Self-propelled Wrapping Packaging Robot

Analysis of the Influence of the Parameters of the Pendulum Mechanism of the Swashplate Engine on the Dynamic Performance

Design and Analysis of Upper Limb Rehabilitation Robots with Fully-actuated Shoulder Joints

The Design and Simulation of a Quadruped Multi-mode Mobile Robot

Gait Analysis and Simulation of a Multi-mode 4-UPU Mechanism

Related Author

No data

Related Institution

Zhengzhou Key Laboratory of Intelligent Assembly Manufacturing and Logistics Optimization, Zhengzhou College of Finance and;Economics

Mechanical and Electrical Engineering Institute, Zhengzhou University of Light Industry

College of Innovation and Entrepreneurship, Henan Open University

School of Mechantronics & Vehicle Engineering, Chongqing Jiaotong University

The Green Aerotechnics Research Institute of Chongqing Jiaotong University

⁰