Effect of Centrifugal Adhesion of Pollutant on Thermal Elastohydrodynamic of Water-lubricated Hybrid Journal Bearing

Zhang Tonggang; Wang Youqiang; Wang Limei; Xu Caihong

doi:10.16578/j.issn.1004.2539.2018.01.003

您当前的位置：

首页 >

文章列表页 >

Effect of Centrifugal Adhesion of Pollutant on Thermal Elastohydrodynamic of Water-lubricated Hybrid Journal Bearing

更新时间：2022-10-20

- Effect of Centrifugal Adhesion of Pollutant on Thermal Elastohydrodynamic of Water-lubricated Hybrid Journal Bearing
- Vol. 42, Issue 1, Pages: 11-16(2018)
- 作者机构：
  
  1. 青岛理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2018.01.003
  CLC：
扫描看全文
[1]张同钢,王优强,王立梅,徐彩红.污染物离心附着现象对水润滑动静压滑动轴承的热弹流影响[J].机械传动,2018,42(01):11-16.

Zhang Tonggang, Wang Youqiang, Wang Limei, et al. Effect of Centrifugal Adhesion of Pollutant on Thermal Elastohydrodynamic of Water-lubricated Hybrid Journal Bearing. [J]. 42(1):11-16(2018)
[1]张同钢,王优强,王立梅,徐彩红.污染物离心附着现象对水润滑动静压滑动轴承的热弹流影响[J].机械传动,2018,42(01):11-16. DOI： 10.16578/j.issn.1004.2539.2018.01.003.

Zhang Tonggang, Wang Youqiang, Wang Limei, et al. Effect of Centrifugal Adhesion of Pollutant on Thermal Elastohydrodynamic of Water-lubricated Hybrid Journal Bearing. [J]. 42(1):11-16(2018) DOI： 10.16578/j.issn.1004.2539.2018.01.003.

摘要

建立了污染物离心附着的弹流润滑几何模型,采用考虑了热效应的Reynolds方程,针对水润滑动静压滑动轴承因为润滑剂污染的问题进行热弹流理论分析。研究了污染物离心附着现象对轴瓦表面纹理的影响以及接触区润滑膜的压力膜厚变化,分析了由于污染物离心附着堵塞进水孔对接触区润滑膜压力膜厚的影响,探究了污染物附着层对接触区温度场的影响。结果显示:污染物的离心附着现象有效改善了轴瓦表面的粗糙形貌,并缓解了接触区的膜厚波动现象;污染物对进水孔的堵塞程度越大,供水压力越小,接触区的最小膜厚越小,最大压力越大,不利于轴承润滑;污染物附着层对水润滑动静压滑动轴承接触区的温度场有影响,当污染物与轴瓦材料的物性参数相差越大温度场变化越大,反之则变化不大。

Abstract

The elastohydrodynamic lubrication geometric model of centrifugal pollutants adhesion is established. The thermal elastohydrodynamic numerical simulation of water-lubricated hybrid journal bearings considering its lubricant pollution problem is carried out by using the Reynolds equation with thermal effect. The effect of centrifugal attachment on the surface texture of the bearing pad and the film thickness,pressure change of the lubricating film in the contact zone are studied. The influence of the film thickness and pressure of the contact zone are analyzed as the contaminants are centrifugally attached to plug the water inlet. The influence of the adhering layer on the temperature field of the contact zone is obtained. The results show that the centrifugal attachment of pollutants effectively improves the roughness of the surface of the bearing pad and alleviates the film thickness fluctuation in the contact area. The greater the degree of clogging of the pollutant to the water inlet,the smaller the water supply pressure,the smaller the minimum film thickness,the greater the maximum pressure,which is not conducive to bearing lubrication. The contaminant adhering layer has an effect on the temperature field of the contact zone of the water-lubricated hybrid journal bearing. When the difference of the physical parameters of the pollutant and the bearing material vary largely,the temperature field changes greatly.

关键词

污染物离心附着水润滑动静压滑动轴承

Keywords

PollutantCentrifugal adhesionWater-lubricatedHybridJournal bearing

references

Views

100

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Analysis of the Thermal Elastohydrodynamic Lubrication of Water-lubricated Hybrid Ceramic Bearing

Research on the Structure Design of Composite Water-lubricated Stern Bearing

Influence of Interfacial Modification on EHL of Journal Bearing

Influence of Fluctuation in Supply Pressure on the Elastohydrodynamic Lubrication（EHL） of Water-lubricated Hybrid Journal Bearing

Related Author

No data

Related Institution

Marine Design and Research Institute of China

School of Mechanical Engineering， Shandong University of Technology， Ji'nan

School of Mechanical Engineering， Shanghai Jiaotong University

School of Mechanical and Automotive Engineering，Qingdao University of Technology

⁰