Numerical Calculation of Stress Intensity Factor of Tooth Root Crack in the High-speed EMU Gear

Li Xiuhong; Wang Yubin; Li Wenhui; Qin Xiaofeng; Pang Yinming

doi:10.16578/j.issn.1004.2539.2017.12.022

您当前的位置：

首页 >

文章列表页 >

Numerical Calculation of Stress Intensity Factor of Tooth Root Crack in the High-speed EMU Gear

更新时间：2022-10-20

- Numerical Calculation of Stress Intensity Factor of Tooth Root Crack in the High-speed EMU Gear
- Vol. 41, Issue 12, Pages: 108-112(2017)
- 作者机构：
  
  1. 太原理工大学机械工程学院精密加工山西省重点实验室
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.12.022
  CLC：
扫描看全文
[1]李秀红,王余滨,李文辉,秦晓峰,庞荫铭.高速动车组齿轮副齿根裂纹应力强度因子数值计算[J].机械传动,2017,41(12):108-112+123.

Li Xiuhong, Wang Yubin, Li Wenhui, et al. Numerical Calculation of Stress Intensity Factor of Tooth Root Crack in the High-speed EMU Gear. [J]. 41(12):108-112(2017)
[1]李秀红,王余滨,李文辉,秦晓峰,庞荫铭.高速动车组齿轮副齿根裂纹应力强度因子数值计算[J].机械传动,2017,41(12):108-112+123. DOI： 10.16578/j.issn.1004.2539.2017.12.022.

Li Xiuhong, Wang Yubin, Li Wenhui, et al. Numerical Calculation of Stress Intensity Factor of Tooth Root Crack in the High-speed EMU Gear. [J]. 41(12):108-112(2017) DOI： 10.16578/j.issn.1004.2539.2017.12.022.

摘要

为研究高速动车组齿轮的齿根裂纹的应力强度因子,结合有限元法和作图法确定了裂纹萌生位置。基于线弹性断裂力学理论,以Abaqus为工具,研究了齿根初始裂纹前缘不同节点处的应力强度因子大小及变化规律,通过对比,确定Ⅰ型应力强度因子在裂纹扩展中占主导地位;在此研究的基础上,探讨了Ⅰ型应力强度因子随载荷、裂纹半径、裂纹形状等因素的变化规律。结果表明,载荷对Ⅰ型应力强度因子大小影响最为显著且呈线性关系;裂纹形状对Ⅰ型应力强度因子在裂纹前缘的分布规律影响十分明显。

Abstract

In order to research the stress intensity factor of tooth root of the high-speed EMU gear,the location of crack initiation is determined by combining the finite element method and mapping method. The stress intensity factor of the different nodes of the initial crack tip of the tooth root is calculated by Abaqus based on the theory of linear elastic fracture mechanics,then by contrast,the type I stress intensity factor is dominant in the crack propagation. Based on the obtained result,the influence of load magnitude,crack radius and crack shape on the mode I stress intensity factor is discussed. The results indicate that the influence of load magnitude on the modeⅠstress intensity factor is obvious and linear. The influence of crack shape on the distribution of mode I stress intensity factor in the crack front is very obvious.

关键词

斜齿轮齿根裂纹三维应力强度因子有限元法

Keywords

Helical gearTooth root crackThree dimensional stress intensity factorFinite element method

references

Views

150

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Time Varying Meshing Stiffness Analysis and Experimental Study of Fatigue Pitting Helical Gear based on Finite Element Method

Study on the Crack Propagation Life of the High-speed Train Gear

Dynamic Response Analysis of the Cracked Fault Gear System Based on the Finite Element Model

Research on the Time-varying Meshing Stiffness Algorithm of Spur Gears with Large Tooth Number Cracks

Contact Analysis of Sprag-type Overrunning Clutches

Related Author

No data

Related Institution

Tianjin Key Laboratory of Power Transmission and Safety Technology for New Energy Vehicles

College of Mechanical Engineering, Taiyuan University of Technology

Department of Aviation Mechanical Engineering and Management in Qingdao Branch, Naval Aviation University

Nanjing Research Institute on Simulation Technique

Wanxiang Qianchao Co., Ltd.

⁰