Study on the Influence of Mechanical Spindle Axial Movement based on ADAMS Simulation Analysis

Jia Yang; Wu Yalong; Wang Zhongmin; Mao Zhiwei; Zhang Jinjie

doi:10.16578/j.issn.1004.2539.2017.11.020

您当前的位置：

首页 >

文章列表页 >

Study on the Influence of Mechanical Spindle Axial Movement based on ADAMS Simulation Analysis

更新时间：2022-10-20

- Study on the Influence of Mechanical Spindle Axial Movement based on ADAMS Simulation Analysis
- Vol. 41, Issue 11, Pages: 102-105(2017)
- 作者机构：
  
  1. 北京化工大学高端机械装备健康监控与自愈化北京市重点实验室
  2. 河南柴油机重工有限责任公司
  3. 大庆油田有限责任公司第九采油厂
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.11.020
  CLC：
扫描看全文
[1]贾杨,吴亚龙,王忠民,茆志伟,张进杰.基于ADAMS仿真分析的机械窜轴故障影响研究[J].机械传动,2017,41(11):102-105.

Jia Yang, Wu Yalong, Wang Zhongmin, et al. Study on the Influence of Mechanical Spindle Axial Movement based on ADAMS Simulation Analysis. [J]. 41(11):102-105(2017)
[1]贾杨,吴亚龙,王忠民,茆志伟,张进杰.基于ADAMS仿真分析的机械窜轴故障影响研究[J].机械传动,2017,41(11):102-105. DOI： 10.16578/j.issn.1004.2539.2017.11.020.

Jia Yang, Wu Yalong, Wang Zhongmin, et al. Study on the Influence of Mechanical Spindle Axial Movement based on ADAMS Simulation Analysis. [J]. 41(11):102-105(2017) DOI： 10.16578/j.issn.1004.2539.2017.11.020.

摘要

基于柴油机窜轴导致传动齿轮断齿故障案例,针对该故障实验模拟难度大,窜动量、窜动形式无法控制,无有效方法提取窜轴时齿轮载荷进行分析的现状,综合运用Creo、ADAMS软件建立柴油机齿轮系动力学仿真模型。进行无窜轴、单向窜轴、往复窜动3种工况的仿真,提取曲轴窜动量与传动齿轮接触力进行关联性分析,得到了发生窜轴故障后齿轮动态载荷变化规律。验证了窜轴会导致齿轮过载、调幅及冲击振动。证明了借助动力学仿真技术进行窜轴故障影响研究具有可行性。

Abstract

Based on a gear tooth fracture case,which is caused by diesel engine crankshaft axial movement. Aiming at the situation that it’s difficult to simulate this fault by experiment,the displacement and movement type can’ t be control. And there is no effective method to extract gear load during the crankshaft axial movement for analysis by experiment. By using Creo,ADAMS software,the gear transmission system dynamics simulation model is built and the no axial movement,one-way axial movement and reciprocating axial movement scenarios is simulated. The gear load change rules during the shaft axial movement is got by extracting the shaft displacement,the gear load and analyzing the relationship between them. The shaft axial movement can cause gears over load,amplitude modulation and impact vibration is verified. The feasibility of the study on the influence of spindle axial movement based on dynamics simulation is proved.

关键词

窜轴断齿动力学仿真故障影响研究

Keywords

Spindle axial movementGear tooth fractureDynamics simulationFailure influence study

references

Views

147

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation Analysis and Experimental Research on a Vibration Damping Structure of Cylindrical Spur Gear Slot Holes

Simulation and Analysis of Dynamics of Lower Limb Exoskeleton Rehabilitation Robots

Structure Design and Kinematics Simulation of a Novel 7-DOF Upper Limb Rehabilitation Exoskeleton Robot

Underactuated Spatial Mechanism of Vehicle Door Latch with Force Constraint

Double-layer Compliant Intermittent Mechanism for Single-drive Electric Opening Latch Safety Branch Chain

Related Author

No data

Related Institution

Luoyang Keda Gear Transmission Research Institute Co., Ltd.

School of Mechatronics Engineering, Henan University of Science and Technology

School of Information and Electronic Technology, Jiamusi University

Harbin Bearing Group Corporation

School of Mechanical Engineering, Jiamusi University

⁰