Research of the Method of Selection of Modification Coefficient Value of the Planetary Involute Gear with Small Teeth Difference based on Matlab

Feng Ding; Yang Hang; Feng Yijing; Wang Jie; Xiang Zhengxin; Wu Han

doi:10.16578/j.issn.1004.2539.2017.07.004

您当前的位置：

首页 >

文章列表页 >

Research of the Method of Selection of Modification Coefficient Value of the Planetary Involute Gear with Small Teeth Difference based on Matlab

更新时间：2022-10-20

- Research of the Method of Selection of Modification Coefficient Value of the Planetary Involute Gear with Small Teeth Difference based on Matlab
- Vol. 41, Issue 7, Pages: 18-21(2017)
- 作者机构：
  
  1. 长江大学机械工程学院
  2. 湖北省油气钻完井工具工程技术研究中心
  3. 中国石油大学(北京)机械与储运工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.07.004
  CLC：
扫描看全文
[1]冯定,杨行,冯一璟,王杰,向正新,吴晗.基于Matlab的渐开线少齿差行星齿轮变位系数取值方法研究[J].机械传动,2017,41(07):18-21.

Feng Ding, Yang Hang, Feng Yijing, et al. Research of the Method of Selection of Modification Coefficient Value of the Planetary Involute Gear with Small Teeth Difference based on Matlab. [J]. 41(7):18-21(2017)
[1]冯定,杨行,冯一璟,王杰,向正新,吴晗.基于Matlab的渐开线少齿差行星齿轮变位系数取值方法研究[J].机械传动,2017,41(07):18-21. DOI： 10.16578/j.issn.1004.2539.2017.07.004.

Feng Ding, Yang Hang, Feng Yijing, et al. Research of the Method of Selection of Modification Coefficient Value of the Planetary Involute Gear with Small Teeth Difference based on Matlab. [J]. 41(7):18-21(2017) DOI： 10.16578/j.issn.1004.2539.2017.07.004.

摘要

根据少齿差行星齿轮传动的定义可知,变位系数的取值是少齿差行星齿轮减速器设计的关键;通过分析和对比常用变位系数选取方法,基于变位齿轮变位系数选择的限制条件理论,并使用Matlab软件进行辅助计算,提出了一个渐开线少齿差行星齿轮变位系数的取值方法;实例验证得到Matlab编程比常规设计计算出的外齿轮变位系数小但重合度却大,结果表明Matlab编程可行性较高。

Abstract

According to the definition of planetary gear transmission with small teeth difference,the selection of value of modification coefficient is the key in the design of planetary gear reducer with small teeth difference. By analyzing and comparing common modification coefficient selection method,based on the constraints theory of the displacement gear modification coefficient selection and using Matlab software assisted calculation,a small teeth difference planetary involute gear modification coefficient value selection method is presented.Through the examples of validation,the external gear modification coefficient calculated by Matlab programming is smaller than calculated by conventional design,but has a large degree of the contact ratio,the results show the feasibility of Matlab programming is higher.

关键词

少齿差行星传动变位系数Matlab

Keywords

Small teeth differencePlanetary transmissionModification coefficientMatlab

references

Views

278

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Kinematics Analysis and Simulation of Cement Filling Automatic Bag Inserting Manipulators

Kinematics Analysis of the Circuit Board Gripper Mechanism

Research on Dynamic Characteristics of Robot Joint System Under Impact Load

Mechanism Optimization Design of Multi-bar Light-load Stamping Press

Transient Thermo Elastohydrodynamic Lubrication of Asymmetric Polymer Planetary Gear with Addendum Modification

Related Author

No data

Related Institution

College of Mechanical Engineering, Tongji University

School of Mechanical Engineering, Shanghai Jiao Tong University

School of Mechanical Engineering， Tiangong University

Tianjin Key Laboratory of Modern Electromechanical Equipment Technology

Shenzhen Hefa Gear Machinery Co.， Ltd.

⁰