Analysis of Tooth Surface Envelope Forming and Top-cut of Face Gear

Feng Zhanrong; Yao Kunpeng; Wang Lixia; Cui Junhua

doi:10.16578/j.issn.1004.2539.2017.06.004

您当前的位置：

首页 >

文章列表页 >

Analysis of Tooth Surface Envelope Forming and Top-cut of Face Gear

更新时间：2022-10-20

- Analysis of Tooth Surface Envelope Forming and Top-cut of Face Gear
- Vol. 41, Issue 6, Pages: 21-24(2017)
- 作者机构：
  
  1. 南昌航空大学航空制造工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.06.004
  CLC：
扫描看全文
[1]冯占荣,姚昆鹏,王利霞,崔俊华.面齿轮齿面包络成形及顶切分析[J].机械传动,2017,41(06):21-24+29.

Feng Zhanrong, Yao Kunpeng, Wang Lixia, et al. Analysis of Tooth Surface Envelope Forming and Top-cut of Face Gear. [J]. 41(6):21-24(2017)
[1]冯占荣,姚昆鹏,王利霞,崔俊华.面齿轮齿面包络成形及顶切分析[J].机械传动,2017,41(06):21-24+29. DOI： 10.16578/j.issn.1004.2539.2017.06.004.

Feng Zhanrong, Yao Kunpeng, Wang Lixia, et al. Analysis of Tooth Surface Envelope Forming and Top-cut of Face Gear. [J]. 41(6):21-24(2017) DOI： 10.16578/j.issn.1004.2539.2017.06.004.

摘要

为了显式的成形面齿轮齿面模型,并对面齿轮产生顶切时最小内半径的精确求解,建立了正交面齿轮包络坐标系,给出了产形齿轮齿面方程,推导了面齿轮工作齿面方程、过渡曲面方程和顶切曲面方程。根据齿面方程,利用MATLAB7.5、CATIA V5对面齿轮齿面进行了仿真分析,根据齿面仿真对比及对顶切界限线的分析,得到了产生顶切时最小内半径关键点,即面齿轮齿顶圆柱面与顶切界限线的交点,通过显式求解该关键点即可得到面齿轮不产生顶切的最小内半径,通过与现有文献中隐式求解内半径结果进行对比得两者数值上相差较小,最后通过仿真切齿的方式进一步说明所述方法的精确度优于其他文献中的方法。

Abstract

In order to explicitly solve the tooth surface model of forming face gear,and exactly solve the minimum inner radius of face gear with top-cut. The orthogonal face gear envelope coordinate system is established and the tooth surface equation of generating gear is given. The face gear working tooth surface equation,transition surface equation and top-cut surface equation are derived. According to the tooth surface equation,the simulation analysis of face gear tooth surface is carried out by using the MATLAB 7. 5 and CATIA V5. According to the simulation comparison of tooth surface and the analysis of top-cut boundary line,the top-cut minimum inner radius key point is got,the key point is the intersection of the face gear tip surface and top-cut boundary line. Through the explicit solving the key points,the minimum inner radius of the face gear without top-cut can be got. Comparing with the existing literature results of the implicitly solving inner radius,and the difference on numerical is small between the two. Finally,through the simulation cutting tooth way,it shows the accuracy of this method is superior to the method of literature.

关键词

面齿轮齿面方程顶切内半径

Keywords

Face gearTooth surface equationTop-cutInside radius

references

Views

126

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Design of Face Gear Tooth Surface of Circular Arc Profile

Establishment of a Prediction Model for the Residual Stress on the Surface Layer of Face Gears During Hot Rolling

Research on Tooth Wear Testing Technology of Face Gears Based on Reverse Engineering

Analysis of Influence of Pinion Tooth Trace Modification on Tooth Surface of Curved Tooth Face Gear

Summary of Progress in Face Gear Processing

Related Author

No data

Related Institution

School of Aeronautical Manufacturing Engineering,Nanchang Hangkong University

Changqing Drilling Co., Ltd., CNPC Chuanqing Drilling Engineering Co., Ltd.

School of Mechanical and Electrical Engineering, Henan University of Science and Technology

School of Mechanical Engineering & Automation, Beijing University of Aeronautics and Astronautics

School of Electrical and Information Engineering, Liaoning Institute of Science and Technology

⁰