Effects of High Order Modification of Work Head Setting on Tooth Flank Form and Contact Zone of Spiral Bevel Gear

Huang Gang; Zhang Weiqing; Guo Xiaodong; Wang Ge; Wen Yikai

doi:10.16578/j.issn.1004.2539.2017.05.002

您当前的位置：

首页 >

文章列表页 >

Effects of High Order Modification of Work Head Setting on Tooth Flank Form and Contact Zone of Spiral Bevel Gear

更新时间：2022-10-20

- Effects of High Order Modification of Work Head Setting on Tooth Flank Form and Contact Zone of Spiral Bevel Gear
- Vol. 41, Issue 5, Pages: 5-9(2017)
- 作者机构：
  
  1. 重庆理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.05.002
  CLC：
扫描看全文
[1]黄刚,张卫青,郭晓东,王戈,文怿恺.水平轮位的高阶修正对弧齿锥齿轮齿形及接触区的影响[J].机械传动,2017,41(05):5-9.

Huang Gang, Zhang Weiqing, Guo Xiaodong, et al. Effects of High Order Modification of Work Head Setting on Tooth Flank Form and Contact Zone of Spiral Bevel Gear. [J]. 41(5):5-9(2017)
[1]黄刚,张卫青,郭晓东,王戈,文怿恺.水平轮位的高阶修正对弧齿锥齿轮齿形及接触区的影响[J].机械传动,2017,41(05):5-9. DOI： 10.16578/j.issn.1004.2539.2017.05.002.

Huang Gang, Zhang Weiqing, Guo Xiaodong, et al. Effects of High Order Modification of Work Head Setting on Tooth Flank Form and Contact Zone of Spiral Bevel Gear. [J]. 41(5):5-9(2017) DOI： 10.16578/j.issn.1004.2539.2017.05.002.

摘要

根据弧齿锥齿轮小轮展成法加工原理和相对运动学理论,建立了带有水平轮位高阶修正式的齿面方程。以一对弧齿锥齿轮的小轮工作齿面为例,利用Matlab软件编写程序求出水平轮位修正后的齿面坐标,通过对所求解出的齿面进行误差曲面构建和接触区可视化编程计算,分析了水平轮位的高阶修正对弧齿锥齿轮齿面形状和接触区的影响规律,研究结果为更自由的控制弧齿锥齿轮齿面形状和接触区位置提供理论依据和重要参考。

Abstract

Based on the generating theory of the pinion of spiral bevel gears and the relative motion theory,the tooth flank equation with the work head setting high order modification formula is established. According to the manufacturing parameters of the working gear flank of a spiral bevel gear set,a program is written on the platform of Matlab to calculate the modified tooth flank coordinates. Through constructing tooth flank form error figures and computing contact zones of the calculated tooth flank,the effects of work head setting high order modification on tooth flank form and contact zone of spiral bevel gears are analyzed,which can provide theoretical basis and valuable reference to facilitate the control of tooth flank form and contact zone of spiral bevel gear.

关键词

弧齿锥齿轮水平轮位高阶修正齿形接触区

Keywords

Spiral bevel gearWork head settingHigh order modificationTooth flank formContact zone

references

Views

106

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Modification Design and Experimental Verification of Spiral Bevel Gear Tooth Surface Based on Quantitative Mismatch

Simulation Analysis of Residual Stresses in Spiral Bevel Gear Machining Based on an Oblique Cutting Model

Influence of Error Factors on Transmission Contact for Spiral Bevel Gears

Research on Modal Analysis of the Spiral Bevel Gear System

Simulation and Experimental Verification of Barrel Finishing of Spiral Bevel Gears Based on the DEM

Related Author

No data

Related Institution

Zhejiang Tongli Transmission Technology Co., Ltd., Rui'an

School of Mechatronics Engineering, Henan University of Science and Technology

Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University

Department of Mechanical Systems, AECC Commercial Aircraft Engine Co., Ltd.

Office for Military Representatives of the PLA Rocket Force Armament Department in Changzhi

⁰