Research of the Three-dimensional Model of Point-line Meshing Gear based on SolidWorks

Yang Fan; Luo Qihan; Huang Hai; Teng Fei

doi:10.16578/j.issn.1004.2539.2017.03.009

您当前的位置：

首页 >

文章列表页 >

Research of the Three-dimensional Model of Point-line Meshing Gear based on SolidWorks

更新时间：2022-10-20

- Research of the Three-dimensional Model of Point-line Meshing Gear based on SolidWorks
- Vol. 41, Issue 3, Pages: 44-49(2017)
- 作者机构：
  
  1. 武汉理工大学物流工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.03.009
  CLC：
扫描看全文
[1]杨帆,罗齐汉,黄海,腾飞.基于SolidWorks的点线啮合齿轮三维模型的研究[J].机械传动,2017,41(03):44-49.

Yang Fan, Luo Qihan, Huang Hai, et al. Research of the Three-dimensional Model of Point-line Meshing Gear based on SolidWorks. [J]. 41(3):44-49(2017)
[1]杨帆,罗齐汉,黄海,腾飞.基于SolidWorks的点线啮合齿轮三维模型的研究[J].机械传动,2017,41(03):44-49. DOI： 10.16578/j.issn.1004.2539.2017.03.009.

Yang Fan, Luo Qihan, Huang Hai, et al. Research of the Three-dimensional Model of Point-line Meshing Gear based on SolidWorks. [J]. 41(3):44-49(2017) DOI： 10.16578/j.issn.1004.2539.2017.03.009.

摘要

基于DZLY180型减速器,针对点线啮合齿轮齿廓的特殊性,利用点线啮合齿轮齿廓的曲线方程,计算修形后齿廓曲线上的若干坐标,通过三次样条曲线对其进行拟合,并运用三维软件Solid Works拟合出修形后的点线啮合齿轮的齿廓曲线,然后进行三维建模,并完成了齿轮的无干涉装配,仿真表明该方法实现了点线啮合齿轮在啮合过程中全局无干涉。

Abstract

Based on the type of DZLY180 gear reducer,aiming at the particularity of the tooth profile of point- line meshing gear,the curve equation of the tooth profile of point- line meshing gear is applied to calculate some coordinates on the tooth profile curve after modification. The cubic spline curves are used to fit the data,and 3D Software Solidworks is used to fit the tooth profile curve of point- line meshing gear. Then the three- dimensional modeling is carried out,the interference- free assembly of the gear is completed. The simulation results show that,the overall interference- free assembly in the meshing process of the point- line meshing gear is realized by the method.

关键词

点线啮合齿轮齿廓曲线修形三次样条曲线三维模型

Keywords

references

Views

140

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Modification and Optimization Design of Motor Train Unit Transmission Gear based on KISSsoft

Study on the Influence of Gear Elastic Deformation on the Dynamic Characteristic of Transmission

Study on Contact Ratio Calculation of Face Gear with Modification based on Gear Tooth Contact Analysis

Related Author

No data

Related Institution

Zhengzhou Research Institute of Mechanical Engineering

Zhengzhou Metro Co.,Ltd.Operation Branch

School of Electromechanical Engineering,Beijing Information Science and Technology University

State Key Laboratory of High Performance Complex Manufacturing, Central South University

⁰