Research and Test for the Cam Steering Mechanism of the S-shaped Carbon-free Car

Chen Yilong; Gao Fengqiang; Xie Zhilong

doi:10.16578/j.issn.1004.2539.2017.01.023

您当前的位置：

首页 >

文章列表页 >

Research and Test for the Cam Steering Mechanism of the S-shaped Carbon-free Car

更新时间：2022-10-20

- Research and Test for the Cam Steering Mechanism of the S-shaped Carbon-free Car
- Vol. 41, Issue 1, Pages: 106-110(2017)
- 作者机构：
  
  1. 厦门大学嘉庚学院机电工程系
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2017.01.023
  CLC：
扫描看全文
[1]陈毅龙,高凤强,谢志龙.S型无碳小车凸轮转向机构研究与试验[J].机械传动,2017,41(01):106-110.

Chen Yilong, Gao Fengqiang, Xie Zhilong. Research and Test for the Cam Steering Mechanism of the S-shaped Carbon-free Car. [J]. 41(1):106-110(2017)
[1]陈毅龙,高凤强,谢志龙.S型无碳小车凸轮转向机构研究与试验[J].机械传动,2017,41(01):106-110. DOI： 10.16578/j.issn.1004.2539.2017.01.023.

Chen Yilong, Gao Fengqiang, Xie Zhilong. Research and Test for the Cam Steering Mechanism of the S-shaped Carbon-free Car. [J]. 41(1):106-110(2017) DOI： 10.16578/j.issn.1004.2539.2017.01.023.

摘要

为了获得运动规律对称且易于微调的S型无碳小车转向机构,提出了凸轮-摇杆滑块的机构模型,采用ADAMS软件对其进行运动学仿真。首先通过参数化建模的方法研究并设计摇杆滑块机构,然后通过反求法获得凸轮轮廓,最后建立凸轮-摇杆滑块机构整体仿真模型。仿真结果表明,该机构输出的运动规律对称,符合转向要求。同时,设计一套试验装置来验证仿真结果,试验数据表明了仿真模型的正确性与研究方法的可行性,所建仿真模型为S型无碳小车凸轮转向机构设计与相关应用提供参考,所设计试验方法为仿真模型验证与加工装配精度检测提供思路。

Abstract

In order to acquire the S- shaped carbon- free car steering mechanism with symmetrical motion law and easy to adjust,the cam- slider- crank mechanism model is proposed. the model’s motion is symmetrical. The kinematics simulation is carried out by using ADAMS software,the rocker- slider mechanism is studied and designed by using the method of parametric modeling,then cam profile is got by the method of reverse design,finally the cam- rocker- slider simulation model is set up,the simulation results show that the motion law is symmetrical,this model is conforms to the requirements of the steering mechanism. At the same time,a set of test device is designed to verify the simulation results,the test data shows that the correctness of the simulation model and the feasibility of the method,the reference for the design of the S- shaped carbon-free car cam steering mechanism and related applications are provided by the simulation model,the ideas for simulation model validation and accuracy detection are provided by test method.

关键词

无碳小车凸轮转向机构运动学仿真Adams试验

Keywords

Carbon-free carCam steering mechanismKinematics simulationAdamsTest

references

Views

1407

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research and Simulation of Cornering Characteristics on Oil and Gas Pipeline Robots

Comparative Analysis of Strength and Test of Nodular Cast Iron and Aluminum Alloy Boxes for Metro Gearboxes

Kinematic and Dynamic Analysis of an Eight-bar Mechanism in Carton Forming

Design and Analysis of the Driving Mechanism of Multi-DOF Flapping Wing Aircrafts

Principle and Kinematics Analysis of a New Planetary Roller and Roller Pinion Compound Transmission Device

Related Author

No data

Related Institution

Wuhan Qinling Lingke Aviation Power System Co., Ltd.

School of Mechanical and Electrical Engineering, Hubei Green Chemical Equipment Engineering Technology;Research Center of Wuhan Institute of Technology

Beijing Subway Co., Ltd.

School of Mechanical Engineering，Hubei University of Technology

Department of mechanical engineering，Shanxi Institute of Mechanical and Electrical Engineering

⁰