Study on Meshing Mechanism of Teeth Back and Dynamic Contact- impact of Gear Pair

Wei Wei; Yang Guang; Wang Siyu

doi:10.16578/j.issn.1004.2539.2016.12.009

您当前的位置：

首页 >

文章列表页 >

Study on Meshing Mechanism of Teeth Back and Dynamic Contact- impact of Gear Pair

更新时间：2022-10-20

- Study on Meshing Mechanism of Teeth Back and Dynamic Contact- impact of Gear Pair
- Vol. 40, Issue 12, Pages: 42-47(2016)
- 作者机构：
  
  1. 郑州机械研究所
  2. 中国石油天然气股份有限公司独山子石化分公司电子商务部
  3. 山东大学(威海)机电与信息工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.12.009
  CLC：
扫描看全文
[1]魏伟,杨光,王思宇.齿背啮合机理及动态接触冲击研究[J].机械传动,2016,40(12):42-47.

Wei Wei, Yang Guang, Wang Siyu. Study on Meshing Mechanism of Teeth Back and Dynamic Contact- impact of Gear Pair. [J]. 40(12):42-47(2016)
[1]魏伟,杨光,王思宇.齿背啮合机理及动态接触冲击研究[J].机械传动,2016,40(12):42-47. DOI： 10.16578/j.issn.1004.2539.2016.12.009.

Wei Wei, Yang Guang, Wang Siyu. Study on Meshing Mechanism of Teeth Back and Dynamic Contact- impact of Gear Pair. [J]. 40(12):42-47(2016) DOI： 10.16578/j.issn.1004.2539.2016.12.009.

摘要

针对齿背啮合冲击引起传动效率、平稳性降低以及振动、噪声加大等问题,考虑齿轮误差、轮齿变形和齿侧间隙,研究齿轮啮合过程中齿背啮合机理。基于有限元动态接触模型,对齿轮啮合特性进行仿真,研究转速和负载对齿背啮合的作用效应。结果表明,一定的转速与负载下,出现轮齿正常啮合与齿背啮合交变;主动轮转速的增大会使齿背啮合冲击加剧,从动轮负载一定幅度内的增大会使得齿背啮合冲击有所减弱。齿背啮合发生时,正常啮合齿对的接触力在零与峰值之间振荡,实际齿轮啮合呈现"正常啮合-脱啮-齿背啮合-正常啮合"规律性的变化。该研究对于齿轮系统的减振与降噪设计具有一定的参考意义。

Abstract

The meshing impact of teeth back which may lead to the phenomenon of low- transmission efficiency,poor accuracy and the decreased stability is studied by considering the teeth backlash,errors and deformation of the gears. Based on the finite element model of dynamic contact of the spur gears,the effects of rotate speed and load on the back meshing is obtained by simulating the meshing characteristic of the gear. The research result shows that both normal meshing and back meshing of gear teeth exist alternately in a certain speed and load condition. The impact of back meshing becomes serious with the increase of the speed of the driving gear. While,it may be weakened with the increase of the load applied on the driven gear within a certain level. When the phenomenon of back meshing happens in the meshing process,the contact force on the normal surface changes between zero and peak magnitude. At the same time,the actual meshing process of gear pairs is a regular cycling changes of normal meshing,mesh apart,back meshing,normal meshing. The study has a certain reference value for designing gear system in the aspects of reducing vibration and noise.

关键词

齿背啮合动态接触啮合冲击脱啮接触力

Keywords

Back meshingDynamic contactMeshing impactMesh-apartContact force

references

Views

143

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Finite Element Analysis of Dynamic Meshing Characteristic of Skew Bevel Gear with Equivocal Modification

Discussion on Main Influencing Factor of Wear Resistance of Pre-lubricating Roller Chain

Optimization Design and Grasping Stability Analysis of Under-actuated Multi-finger Manipulator

Research of Internal Excitation of Helical Gear Meshing Transmission

Related Author

No data

Related Institution

School of Mechanical Engineering，Southwest Jiaotong University

Qingdao Choho Industrial Co.，Ltd.

School of Mechanical Engineering，Inner Mongolia University of Technology

Pan Asia Technical Automotive Center Co., Ltd.

Shanghai Collaborative Innovation Center of Intelligent Manufacturing Robot Technology for Large Components

⁰