Comparison between ISO and AGMA Bevel Gear Strength Calculation Standard

Zou Youming; Liu Shaojun

doi:10.16578/j.issn.1004.2539.2016.09.041

您当前的位置：

首页 >

文章列表页 >

Comparison between ISO and AGMA Bevel Gear Strength Calculation Standard

更新时间：2022-10-20

- Comparison between ISO and AGMA Bevel Gear Strength Calculation Standard
- Vol. 40, Issue 9, Pages: 187-192(2016)
- 作者机构：
  
  1. 中南大学机电工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.09.041
  CLC：
扫描看全文
[1]邹又名,刘少军.ISO与AGMA锥齿轮强度计算标准比较[J].机械传动,2016,40(09):187-192.

Zou Youming, Liu Shaojun. Comparison between ISO and AGMA Bevel Gear Strength Calculation Standard. [J]. 40(9):187-192(2016)
[1]邹又名,刘少军.ISO与AGMA锥齿轮强度计算标准比较[J].机械传动,2016,40(09):187-192. DOI： 10.16578/j.issn.1004.2539.2016.09.041.

Zou Youming, Liu Shaojun. Comparison between ISO and AGMA Bevel Gear Strength Calculation Standard. [J]. 40(9):187-192(2016) DOI： 10.16578/j.issn.1004.2539.2016.09.041.

摘要

分析和比较了国际标准化组织（ISO）与美国齿轮制造协会（AGMA）标准关于锥齿轮传动的强度计算方法的差异,采用分类比较和实例对比的方法分析了两种标准修正系数的含义和差异,以及齿轮参数变化对强度计算结果的影响。研究表明,齿轮参数和修正系数的取值不同是导致两标准计算结果差异的原因,其中载荷、几何参数材料特性与表面状况类因数为主要影响因数,AGMA标准的接触强度计算偏向保守,而ISO标准的弯曲强度计算偏向保守。

Abstract

The difference of bevel gear strength rating methods between ISO standard and AGMA standard is analyzed and compared. The meaning of correction factors and differences between the two standards are analyzed through classifications and examples,and the gear parameters effects on gear rating results are also analyzed. The study indicates that it is the different values of parameters and correction factors that cause the differences in gear rating results of the two standards,and the load,geometry parameters,material property and surface condition have the most significant effects. The AGMA standard tends to be conservative in the calculation of contact strength,whereas ISO standard tends to be conservative in the calculation of bending strength.

关键词

ISO标准AGMA标准锥齿轮齿轮强度比较

Keywords

ISO standardAGMA standardBevel gearGear strengthComparison

references

Views

151

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Comparison Between HB and ISO Standard for Calculating Bevel Gear Tooth Surface Contact Fatigue Strength

Backlash Control and the Fatigue Life Bench Test of Bevel Gears from Inter-axle Differential

Discussing the Cutting Method of Skew Bevel Bear based on the Tooth Surface Generating Line

Application of Spiral Ring Damper for Aeroengine Bevel Gears

Non-orthogonal Bevel Gear Design and Strength Analysis for Variable Incline Angle Swashplate Driving Stirling Engine

Related Author

No data

Related Institution

Key Laboratory of Power Transmission Technology on Aero-engine， Aero Engine Corporation of China

Shenyang Engine Research Institute， Aero-engine Corporation of China

Training Base, Army Engineering University of PLA

College of Mechanical and Electric Engineering，Changchun University of Science and Technology

Sichuan Gas Turbine Establishment, Aero Engine Corporation of China

⁰