Theoretical Research of the Machining of the Few Tooth Number Gear with the Y38 Hobbing Machine

Wang Baomin; Guo Hongfeng; Chen Changbiao; Ma Yuelin; Chai Xiaoyu

doi:10.16578/j.issn.1004.2539.2016.08.035

您当前的位置：

首页 >

文章列表页 >

Theoretical Research of the Machining of the Few Tooth Number Gear with the Y38 Hobbing Machine

更新时间：2022-10-20

- Theoretical Research of the Machining of the Few Tooth Number Gear with the Y38 Hobbing Machine
- Vol. 40, Issue 8, Pages: 160-162(2016)
- 作者机构：
  
  1. 陕西理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.08.035
  CLC：
扫描看全文
[1]王保民,郭宏枫,陈长标,马跃林,柴晓玉.Y38滚齿机加工少齿数齿轮的理论研究[J].机械传动,2016,40(08):160-162.

Wang Baomin, Guo Hongfeng, Chen Changbiao, et al. Theoretical Research of the Machining of the Few Tooth Number Gear with the Y38 Hobbing Machine. [J]. 40(8):160-162(2016)
[1]王保民,郭宏枫,陈长标,马跃林,柴晓玉.Y38滚齿机加工少齿数齿轮的理论研究[J].机械传动,2016,40(08):160-162. DOI： 10.16578/j.issn.1004.2539.2016.08.035.

Wang Baomin, Guo Hongfeng, Chen Changbiao, et al. Theoretical Research of the Machining of the Few Tooth Number Gear with the Y38 Hobbing Machine. [J]. 40(8):160-162(2016) DOI： 10.16578/j.issn.1004.2539.2016.08.035.

摘要

根据范成法原理和Y38滚齿机备用挂轮情况,从理论上分析了Y38滚齿机加工齿数小于8的少齿数齿轮的可行性;在实验的基础上,分析了加工少齿数齿轮时滚齿机不能正常启动的原因,并提出了改造方案,改造后的Y38滚齿机可以加工出少齿数齿轮。

Abstract

According to the principle of generation method and the case of Y38 hobbing machine spare wheels,the feasibility of the machining of few tooth gear with tooth number less than eight by using Y38 hobbing machine is theoretically analyzed. On the basis of the experiment,the reason why the hobbing machine can ’t start normally when machining the few teeth number gear is analyzed,and the renovation scheme is put forward.After transforming,the few tooth number gear can be machined by using the Y38 hobbing machine.

关键词

范成法滚齿机少齿数齿轮

Keywords

Generation methodHobbing machineFew tooth number gear

references

Views

101

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research of the Virtual Machining Method of Vehicle Variable Ratio Gear based on Generation Method

Design of Hybrid-driving Transmission System of Hobbing Machine

Related Author

No data

Related Institution

Jingzhou Henglong Automobile Parts Manufacture Co.,Ltd.

School of Mechanical and Electronic Engineering,Wuhan University of Technology

Mechanical and Electronic Engineering Department,Foshan University

⁰