Influence of Microscopic Particle Flow on Thermal Elastohydrodynamic Lubrication of Spur Gear

Huang Xingbao; Wang Youqiang; Liu Qian; Dong Ning

doi:10.16578/j.issn.1004.2539.2016.06.005

您当前的位置：

首页 >

文章列表页 >

Influence of Microscopic Particle Flow on Thermal Elastohydrodynamic Lubrication of Spur Gear

更新时间：2022-10-20

- Influence of Microscopic Particle Flow on Thermal Elastohydrodynamic Lubrication of Spur Gear
- Vol. 40, Issue 6, Pages: 23-26(2016)
- 作者机构：
  
  1. 青岛理工大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.06.005
  CLC：
扫描看全文
[1]黄兴保,王优强,刘前,董宁.微观颗粒流对直齿轮热弹流润滑的影响[J].机械传动,2016,40(06):23-26+62.

Huang Xingbao, Wang Youqiang, Liu Qian, et al. Influence of Microscopic Particle Flow on Thermal Elastohydrodynamic Lubrication of Spur Gear. [J]. 40(6):23-26(2016)
[1]黄兴保,王优强,刘前,董宁.微观颗粒流对直齿轮热弹流润滑的影响[J].机械传动,2016,40(06):23-26+62. DOI： 10.16578/j.issn.1004.2539.2016.06.005.

Huang Xingbao, Wang Youqiang, Liu Qian, et al. Influence of Microscopic Particle Flow on Thermal Elastohydrodynamic Lubrication of Spur Gear. [J]. 40(6):23-26(2016) DOI： 10.16578/j.issn.1004.2539.2016.06.005.

摘要

建立了粉末状颗粒流润滑数学模型,考虑了颗粒流对润滑油流变黏度和密度的定量影响,计入了时变效应和热效应,对直齿轮进行了热弹流润滑研究,分析了不同质量分数的Mo S2对压力、膜厚和温度的影响,比较了质量分数为5%的人造金刚石、45钢、石墨和Mo S2颗粒对压力、膜厚和温度的影响,最后与现有实验结果进行了比较验证。结果表明,Mo S2颗粒质量分数增大,最大温度有所降低,最小膜厚也减小明显,节点接触中心瞬态温升减小显著;摩擦因数和硬度很低的石墨和Mo S2颗粒流具有较好的润滑效果,而摩擦因数和硬度高的人造金刚石和45钢颗粒流对润滑不利。

Abstract

The powder particles flow lubrication mathematical model is established. The thermal elastohydrodynamic lubrication of spur gears are investigated with considering quantitative influence of particles flow on oil rheological viscosity and density,reckoning in time-varying effect and thermal effect. The influence of different mass fraction of MoS,2, on film pressure,film thickness and temperature are analyzed. The influences of synthetic diamond,45 steel,graphite and MoS,2, with 5% mass fraction on film pressure,film thickness and temperature are compared. Finally,the comparative validation is carried out according to the existing experimental results. Results show that the noticeable increase in mass fraction of MoS,2, may cause a slight reduction in the maximum temperature,a remarkable reduction in the minimum film thickness and a distinct reduction in contact centre transient temperature at pitch point. The graphite and MoS,2, particles flow with low friction coefficient and low hardness have preferable lubrication effects. However,the synthetic diamond and 45 steel particles flow with high friction coefficient and high hardness are harmful to lubrication.

关键词

颗粒流二硫化钼直齿轮弹流润滑热效应

Keywords

Particles flowMoS2Spur gearElastohydrodynamic lubricationThermal effect

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on the Time-varying Meshing Stiffness Algorithm of Spur Gears Based on an Improved Potential Energy Method

Analysis of Transient Elastohydrodynamic Lubrication of Asymmetric Polymer Planetary Gears

Study on Tooth Wear of Spur Gears Under the Mixed Elastohydrodynamic Lubrication

Analysis of Factors Affecting Lubrication Performance of Crankshaft Main Bearing Considering Thermal Effect

Influence of Roughness on Isothermal Elastohydrodynamic Lubrication of Roller Enveloped Worm Drive

Related Author

No data

Related Institution

Department of Aviation Mechanical Engineering and Management in Qingdao Branch, Naval Aviation University

Key Laboratory of Industrial Fluid Energy Conservation and Pollution Control, Ministry of Education

School of Mechanical & Automotive Engineering, Qingdao University of Technology

Department of Intelligent Manufacturing and Industrial Safety, Chongqing Vocational Institute of Safety Technology

School of Information and Intelligent Manufacturing, Chongqing City Vocational College

⁰