Study on the Contour Design of Disc Cam with Offset Translation Pushrod based on Solid Works and Matlab

Liu Xueshen; Wang Zhen; Ai Zetan; Jiang Zhiqiang

doi:10.16578/j.issn.1004.2539.2016.05.018

您当前的位置：

首页 >

文章列表页 >

Study on the Contour Design of Disc Cam with Offset Translation Pushrod based on Solid Works and Matlab

更新时间：2022-10-20

- Study on the Contour Design of Disc Cam with Offset Translation Pushrod based on Solid Works and Matlab
- Vol. 40, Issue 5, Pages: 77-79(2016)
- 作者机构：
  
  1. 郑州航空工业管理学院机电工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.05.018
  CLC：
扫描看全文
[1]刘学申,王振,艾泽谭,蒋志强.基于Matlab和SolidWorks的偏置直动推杆盘状凸轮轮廓设计研究[J].机械传动,2016,40(05):77-79+104.

Liu Xueshen, Wang Zhen, Ai Zetan, et al. Study on the Contour Design of Disc Cam with Offset Translation Pushrod based on Solid Works and Matlab. [J]. 40(5):77-79(2016)
[1]刘学申,王振,艾泽谭,蒋志强.基于Matlab和SolidWorks的偏置直动推杆盘状凸轮轮廓设计研究[J].机械传动,2016,40(05):77-79+104. DOI： 10.16578/j.issn.1004.2539.2016.05.018.

Liu Xueshen, Wang Zhen, Ai Zetan, et al. Study on the Contour Design of Disc Cam with Offset Translation Pushrod based on Solid Works and Matlab. [J]. 40(5):77-79(2016) DOI： 10.16578/j.issn.1004.2539.2016.05.018.

摘要

传统设计凸轮轮廓线方法计算繁琐复杂,求解精度不高且效率低下。利用Matlab编程语言求解并绘制凸轮轮廓曲线的方法,不但能够提高计算精度而且能够缩短设计周期。导出基于Matlab环境中绘制的曲线上的数据点,在Solid Works环境中生成凸轮轮廓曲线草图,并通过拉伸命令完成凸轮的三维模型。该方法简单高效,且便于根据实际工况对凸轮轮廓形状的快速修整,较大的提高了设计效率。

Abstract

The traditional methods of designing cam profile always leads to complicated calculation,low computational accuracy and efficiency. But by using Matlab programming language,the computational accuracy can be increased and the design period can be shortened in the process of solving and drawing cam profile.Firstly,the data points on the curve that are drawn in the Matlab can be derived. Secondly,a rough draft of cam profile is generated in Solid Works. Finally,the three- dimensional model of cam profile is created during the stretching process. This method is easy to operate and can greatly improve the design efficiency by quickly modifying the shape of cam profile according to the actual working conditions.

关键词

凸轮轮廓曲线MatlabSolidWorks

Keywords

CamContour curveMatlabSolid Works

references

Views

358

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Kinematics Analysis and Simulation of Cement Filling Automatic Bag Inserting Manipulators

Kinematics Analysis of the Circuit Board Gripper Mechanism

Mechanism Optimization Design of Multi-bar Light-load Stamping Press

Calculation and Analysis of Modified Gear Time-varying Meshing Stiffness based on Matlab

Scheme Design and Kinematics Analysis of Single Leg Mechanism of Multi-legged Robot

Related Author

No data

Related Institution

College of Mechanical Engineering, Tongji University

School of Mechanical Engineering, Shanghai Jiao Tong University

School of Mechanical Engineering，Hubei University of Technology

Qing'an Group Co.，Ltd.

Inspection Department，Shenyang Zhongzheng Special Equipment Inspection Co.，Ltd.

⁰