Research of Spiral Bevel Gear Tooth Surface Modification Technique based on Machining Center

Wang Lei; Cao Xuemei; Deng Xiaozhong; Lei Baozhen

doi:10.16578/j.issn.1004.2539.2016.02.001

您当前的位置：

首页 >

文章列表页 >

Research of Spiral Bevel Gear Tooth Surface Modification Technique based on Machining Center

更新时间：2022-10-20

- Research of Spiral Bevel Gear Tooth Surface Modification Technique based on Machining Center
- Vol. 40, Issue 2, Pages: 1-5(2016)
- 作者机构：
  
  1. 河南科技大学机电工程学院
  2. 2. 机械装备先进制造河南省协同创新中心
  3. 北京联合大学机电学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2016.02.001
  CLC：
扫描看全文
[1]王磊,曹雪梅,邓效忠,雷保珍.基于加工中心切齿的弧齿锥齿轮齿面修形技术研究[J].机械传动,2016,40(02):1-5.

Wang Lei, Cao Xuemei, Deng Xiaozhong, et al. Research of Spiral Bevel Gear Tooth Surface Modification Technique based on Machining Center. [J]. 40(2):1-5(2016)
[1]王磊,曹雪梅,邓效忠,雷保珍.基于加工中心切齿的弧齿锥齿轮齿面修形技术研究[J].机械传动,2016,40(02):1-5. DOI： 10.16578/j.issn.1004.2539.2016.02.001.

Wang Lei, Cao Xuemei, Deng Xiaozhong, et al. Research of Spiral Bevel Gear Tooth Surface Modification Technique based on Machining Center. [J]. 40(2):1-5(2016) DOI： 10.16578/j.issn.1004.2539.2016.02.001.

摘要

针对现有的弧齿锥齿轮的齿面修形技术局限于专用铣齿机的缺陷,提出了一种基于加工中心切齿的齿面修形方法。基于弧齿锥齿轮大轮成形法加工方式,利用共轭原理推导小轮齿面方程,在离散点上运用差曲面方程附加修形量,通过NURBS曲面啮合得到小轮的数字化齿面,并与大轮理论齿面进行TCA分析;在加工中心上完成了切齿实验,滚动检查实验显示齿面接触区与仿真结果基本一致,证明所提出的修形方法是可行的,为在加工中心上实现弧齿锥齿轮的切齿和啮合质量控制提供了基础。

Abstract

On the consideration of the existing tooth surface modification technology of spiral bevel gear limited to special milling tooth machine,a kind of tooth surface modification method based on the machining center is put forward. Based on the forming machining method of spiral bevel gear,the pinion tooth surface equation is derived by using the conjugate principle,and the amount of modification is added to discrete points by applying the differential curved surface equation. The digital gear tooth surface of the pinion is obtained by the NURBS surface meshing,which is analyzed with the theoretical tooth surface of the gear. The cutting experiment on machining center is performed on the machining center,and the rolling test experiments show that the tooth contact area and the simulation results mainly agreed. The feasibility of the modification method proposed is verified,which provides the technical support for the spiral bevel gear tooth being processed on machining center and the control of the meshing quality.

关键词

弧齿锥齿轮修形TCANURBS加工中心

Keywords

Spiral bevel gearModificationTCANURBSMachining center

references

Views

243

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

NURBS Reconstruction and Optimization Method for the Tooth Surface after Simulation Process of Spiral Bevel Gear

Theoretical Research of the Modification of Cycloidal Gear used in RV Reducer of Robot

Modification Design and Experimental Verification of Spiral Bevel Gear Tooth Surface Based on Quantitative Mismatch

Simulation Analysis of Residual Stresses in Spiral Bevel Gear Machining Based on an Oblique Cutting Model

Influence of Error Factors on Transmission Contact for Spiral Bevel Gears

Related Author

No data

Related Institution

School of Mechanical Engineering, Xinjiang University

State Key Laboratory of High Performance and Complex Manufacturing,Central South University

School of Mechatronics Engineering, Henan University of Science and Technology

Zhejiang Tongli Transmission Technology Co., Ltd., Rui'an

Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University

⁰