Determination of Gear Bending Fatigue Limit based on Up and Down Method

Yang Guangming

doi:10.16578/j.issn.1004.2539.2015.08.042

您当前的位置：

首页 >

文章列表页 >

Determination of Gear Bending Fatigue Limit based on Up and Down Method

更新时间：2022-10-20

- Determination of Gear Bending Fatigue Limit based on Up and Down Method
- Vol. 39, Issue 8, Pages: 176-180(2015)
- 作者机构：
  
  1. 重庆电子工程职业学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2015.08.042
  CLC：
扫描看全文
[1]杨广明.升降法测定齿轮的弯曲疲劳极限[J].机械传动,2015,39(08):176-180.

Yang Guangming. Determination of Gear Bending Fatigue Limit based on Up and Down Method. [J]. 39(8):176-180(2015)
[1]杨广明.升降法测定齿轮的弯曲疲劳极限[J].机械传动,2015,39(08):176-180. DOI： 10.16578/j.issn.1004.2539.2015.08.042.

Yang Guangming. Determination of Gear Bending Fatigue Limit based on Up and Down Method. [J]. 39(8):176-180(2015) DOI： 10.16578/j.issn.1004.2539.2015.08.042.

摘要

齿轮弯曲疲劳强度是衡量齿轮性能的重要指标,开展齿轮试验是获得齿轮弯曲强度的有效方法。针对20Cr Mo H渗碳齿轮,采用升降法开展单齿弯曲疲劳强度试验研究,基于脉动加载法和成组试验方案,在电磁谐振疲劳试验机上对齿轮轮齿进行了5个应力级的疲劳强度试验;依据平截面和折截面两种方法计算轮齿齿根应力,分析得到了该齿轮的弯曲疲劳极限;结合轮齿裂纹位置和断口形貌,分析了形成原因,结果表明,折截面法确定的危险截面位置更加符合实际,为进一步研究齿轮的弯曲疲劳强度提供了基本思路。

Abstract

The bending fatigue strength of gear is an important indicator for gear performance,and it is an effective method to obtain the bending strength according to the test procedure. The test of the single- tooth bending fatigue strength of 20 Cr Mo H carburized gear is discussed. The test method of pulse load in single-tooth and the group method is used in the experiment and the bending fatigue strength test of gear tooth at 5classes of constant stress levels is carried out on the electromagnetic resonance testing machine. By applying planar section method and broken- line section method,the root stress of gear teeth under different load levers is calculated. The macro morphology of fatigue fracture of gear test specimens is analyzed. The result shows that it is more actual to determine the risk position with broken- line section method. It provides a new approach for evaluating the gear bending fatigue strength.

关键词

齿轮弯曲疲劳试验升降法弯曲疲劳极限

Keywords

references

Views

244

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Small Sample Test Statistic Method for the Gear Fatigue Characteristic

Composite Rolling Test Control Method of Gear and Software

Vibration Analysis and Topology Optimization of Gearbox of Electric Vehicle

Design and Implementation of Automatic Detection System of Gear Grinding Burn

Application Status and Development Trend of Lightweight Technology of Crane Gear Transmission Device

Related Author

No data

Related Institution

Beijing Engineering Research Center of Smart Mechanical Innovation Design Service,College of Mechanical and Electrical Engineering,Beijing Union University

Key Laboratory of Advanced Manufacturing Technology for Automobile Parts of Ministry of Education, Chongqing University of Technology

School of Automotive Studies,Tongji University

Sino-German College of Applied Sciences,Tongji University

New Clean Energy Automotive Engineering Center,Tongji University

⁰