Stress Analysis of Meshing Gear with Staggering Tooth

Liu Yaqiong; Wang Tie; Wu Zhifei; Zhang Ruiliang; Shi Ruonan; Wu Ping’an

doi:10.16578/j.issn.1004.2539.2015.06.023

您当前的位置：

首页 >

文章列表页 >

Stress Analysis of Meshing Gear with Staggering Tooth

更新时间：2022-10-20

- Stress Analysis of Meshing Gear with Staggering Tooth
- Vol. 39, Issue 6, Pages: 107-110(2015)
- 作者机构：
  
  1. 太原理工大学齿轮研究所
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2015.06.023
  CLC：
扫描看全文
[1]刘亚琼,王铁,武志斐,张瑞亮,史若男,吴平安.错齿啮合齿轮应力分析[J].机械传动,2015,39(06):107-110.

Liu Yaqiong, Wang Tie, Wu Zhifei, et al. Stress Analysis of Meshing Gear with Staggering Tooth. [J]. 39(6):107-110(2015)
[1]刘亚琼,王铁,武志斐,张瑞亮,史若男,吴平安.错齿啮合齿轮应力分析[J].机械传动,2015,39(06):107-110. DOI： 10.16578/j.issn.1004.2539.2015.06.023.

Liu Yaqiong, Wang Tie, Wu Zhifei, et al. Stress Analysis of Meshing Gear with Staggering Tooth. [J]. 39(6):107-110(2015) DOI： 10.16578/j.issn.1004.2539.2015.06.023.

摘要

针对相同啮合齿宽,对比分析了基于国标计算公式、Romax软件全齿啮合和Romax软件错齿啮合3种方法计算而得的接触应力和弯曲应力结果,进而研究了不同啮合齿宽（即不同错齿量）对齿轮弯曲应力值的影响。同时采用罗卡提快速疲劳试验方法,进行运转式齿轮弯曲疲劳试验,通过3种方法确定各级载荷的弯曲应力值,从而分别获得相应的弯曲疲劳极限估计值。通过对比弯曲疲劳极限估计值,确定了基于Romax软件错齿啮合计算错齿啮合弯曲应力的可信性,为错齿啮合齿轮弯曲应力的计算提供参考方法。

Abstract

The contact stress and bending stress are calculated and comparatively analyzed with the same meshing tooth width by using three methods of the national standard formula based,Romax software（full tooth meshing） and Romax software（staggering tooth meshing）,and thus the effects of different meshing tooth width（that is different staggering tooth amount） on the gear bending stress values are researched.While by using Locati rapid fatigue testing methods,the operating gear bending fatigue tests are carried out and the bending stress of each load with three methods are determined,the bending fatigue limit estimated values are obtained.By comparing the bending fatigue limit estimated value,the bending stress credibility of staggering tooth meshing is determined based on Romax software（staggering tooth meshing）,the reference method for the gear bending stresses calculated with staggering tooth meshing is provided.

关键词

齿轮错齿弯曲应力Romax

Keywords

references

Views

133

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on Allocation Method of Root Bending Stress based on Gear Tangential Modification

Design and Analysis of the Elastic Torsion Shafting in Split Torque Transmission System of Cylindrical Gear

Small Sample Test Statistic Method for the Gear Fatigue Characteristic

Composite Rolling Test Control Method of Gear and Software

Design and Implementation of Automatic Detection System of Gear Grinding Burn

Related Author

No data

Related Institution

Jiangsu City Vocational College Nantong Campus

China Academy of Machinery Science and Technology

Jiangsu Key Laboratory of Precision and Micro-Manufacturing Technology,Nanjing University of Aeronautics and Astronautics

Beijing Engineering Research Center of Smart Mechanical Innovation Design Service,College of Mechanical and Electrical Engineering,Beijing Union University

Key Laboratory of Advanced Manufacturing Technology for Automobile Parts of Ministry of Education, Chongqing University of Technology

⁰