Dynamics Analysis of the Asynchronous Starting of Converter Tilting Mechanism Reducer based on ADAMS

Ren Xueping; Yang Songtao

doi:10.16578/j.issn.1004.2539.2015.05.006

您当前的位置：

首页 >

文章列表页 >

Dynamics Analysis of the Asynchronous Starting of Converter Tilting Mechanism Reducer based on ADAMS

更新时间：2022-10-20

- Dynamics Analysis of the Asynchronous Starting of Converter Tilting Mechanism Reducer based on ADAMS
- Vol. 39, Issue 5, Pages: 154-157(2015)
- 作者机构：
  
  1. 内蒙古科技大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2015.05.006
  CLC：
扫描看全文
[1]任学平,杨松涛.基于ADAMS的转炉倾动机构减速机电机不同步启动动力学分析[J].机械传动,2015,39(05):154-157.

Ren Xueping, Yang Songtao. Dynamics Analysis of the Asynchronous Starting of Converter Tilting Mechanism Reducer based on ADAMS. [J]. 39(5):154-157(2015)
[1]任学平,杨松涛.基于ADAMS的转炉倾动机构减速机电机不同步启动动力学分析[J].机械传动,2015,39(05):154-157. DOI： 10.16578/j.issn.1004.2539.2015.05.006.

Ren Xueping, Yang Songtao. Dynamics Analysis of the Asynchronous Starting of Converter Tilting Mechanism Reducer based on ADAMS. [J]. 39(5):154-157(2015) DOI： 10.16578/j.issn.1004.2539.2015.05.006.

摘要

某钢厂210t转炉倾动机构在生产过程中,曾发生减速器高速轴断裂故障,事后经测试发现,其中一台电机启动较其他3台滞后0.2s。针对此不同步启动现象,在Pro/E中装配出几何实体模型,然后将其导入ADAMS软件,在4台电机不同步启动工况下,对模型进行动力学分析,结果表明不同步启动会造成二级大齿轮和一次减速器末端齿轮轴之间产生巨大冲击力,也使4个一次减速器出现明显不均载情况。

Abstract

In the process of production of a steel plant of 210 tconverter tilting mechanism,there is a fracture failure of the high speed shafts of reducer.Through the test finding that one of the motors start 0.2slater than others.Aiming at this out-sync phenomenon,the geometry entity model of the reducer which is set up in Pro/E is imported into the software ADAMS.In ADAMS,the dynamics analysis of the model is carried out in the case that the four motors are not starting out of step.The results,a conclusion can be drawn that there is a huge impact between the large gear and a gear shaft of reducer,and uneven loads between four gear shafts.

关键词

ADAMSPro/E减速机不同步动力学不均载

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Parameterized Design and Motion Simulation of Swing Piston Pump Movement Mechanism

Overview of Crown Gear Coupling Design Technologies

Dynamics Simulation Analysis of a New-type of Planetary Reducer with Few Teeth Difference used by Pumping Unit based on ADAMS

Simulation Analysis and the Improvement of the Omnibearing Walking Robot

Meshing Characteristic Analysis of the Gear Rack Drilling Rig Hoisting System

Related Author

No data

Related Institution

China Academy of Engineering Physics

School of Mechanical Engineering, Northwestern Polytechnical University

Institute of Process Engineering,Chinese Academy of Science

Zhengzhou Research Institute of Mechanical Engineering

College of Mechanical Engineering,Chongqing Three Gorges University

⁰