Research of the Residual Stress Generation and Influence Factor of Grinding Tooth Surface of Spiral Bevel Gear

Zhou Jing; Ming Xingzu

doi:10.16578/j.issn.1004.2539.2015.03.003

您当前的位置：

首页 >

文章列表页 >

Research of the Residual Stress Generation and Influence Factor of Grinding Tooth Surface of Spiral Bevel Gear

更新时间：2022-10-20

- Research of the Residual Stress Generation and Influence Factor of Grinding Tooth Surface of Spiral Bevel Gear
- Vol. 39, Issue 3, Pages: 9-14(2015)
- 作者机构：
  
  1. 湖南工业大学
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2015.03.003
  CLC：
扫描看全文
[1]周静,明兴祖.弧齿锥齿轮磨削齿面残余应力生成及影响因素研究[J].机械传动,2015,39(03):9-14.

Zhou Jing, Ming Xingzu. Research of the Residual Stress Generation and Influence Factor of Grinding Tooth Surface of Spiral Bevel Gear. [J]. 39(3):9-14(2015)
[1]周静,明兴祖.弧齿锥齿轮磨削齿面残余应力生成及影响因素研究[J].机械传动,2015,39(03):9-14. DOI： 10.16578/j.issn.1004.2539.2015.03.003.

Zhou Jing, Ming Xingzu. Research of the Residual Stress Generation and Influence Factor of Grinding Tooth Surface of Spiral Bevel Gear. [J]. 39(3):9-14(2015) DOI： 10.16578/j.issn.1004.2539.2015.03.003.

摘要

弧齿锥齿轮齿面残余应力是磨削条件下各种因素综合作用而产生的。建立了影响磨削残余应力的磨削基本参数、磨削热和磨削力的数学模型。在有限元3D单齿模型基础上,进行了弧齿锥齿轮磨削残余应力的有限元仿真与分析,并试验验证了此方法是可行的。结果表明:残余压应力呈现在弧齿锥齿轮齿面上,而残余拉应力在齿内;磨削残余应力与磨削深度、砂轮速度、展成速度、磨削液有关;磨削残余应力的降低能有效地预防磨削裂纹。

Abstract

The residual stress of spiral bevel gear on the tooth surface is produce by the comprehensive effect of various factors of grinding conditions.The mathematical model of the grinding basic parameters of the effects on grinding residual stress,grinding heat and grinding force.Based on the finite element 3D model of single tooth,the finite element simulation and analysis of residual stress of spiral bevel gear grinding,and the test shows this method is feasible.The results show the residual stress present in the spiral bevel gear tooth surface,while the residual tensile stress in the tooth,the grinding residual stress is connected with grinding depth,wheel speed,extended speed and grinding fluid.The reducing of grinding residual stress can effectively prevent grinding cracks.

关键词

弧齿锥齿轮磨削残余应力有限元分析磨削裂纹

Keywords

Spiral bevel gearGrindingResidual stressFinite element analysisGrinding crack

references

Views

196

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation Analysis of Residual Stresses in Spiral Bevel Gear Machining Based on an Oblique Cutting Model

Temperature Field Analysis of Grinding Face Gear

Finite Element Analysis of Effect of Double Shot Peening on Residual Stresses of 18CrNiMo7-6 Gear Steel

Finite Element Analysis of Thermal-structural Coupling for an Aeronautical Spiral Bevel Gear

Finite Element Analysis of Loaded Meshing Characteristic of Spiral Bevel Gear

Related Author

No data

Related Institution

School of Mechatronics Engineering, Henan University of Science and Technology

School of Mechanical Engineering， Northwestern Polytechnical University， Xi′an

School of Aerospace Engineering, Zhengzhou University of Aeronautics

Henan Aerospace Hydraulic Pneumatic Technology Co., Ltd.

Zhengzhou Research Institute of Mechanical Engineering Co., Ltd.

⁰