Study on the Structural Innovation and Gear Cutting Experiment of Hypoid Gear for a CNC Milling Machine Tool

Deng Jing; Deng Xiaozhong; Xie Junjun; Jiang Chuang; Geng Longlong

doi:10.16578/j.issn.1004.2539.2015.03.001

您当前的位置：

首页 >

文章列表页 >

Study on the Structural Innovation and Gear Cutting Experiment of Hypoid Gear for a CNC Milling Machine Tool

更新时间：2022-10-20

- Study on the Structural Innovation and Gear Cutting Experiment of Hypoid Gear for a CNC Milling Machine Tool
- Vol. 39, Issue 3, Pages: 1-4(2015)
- 作者机构：
  
  1. 西北工业大学机电学院
  2. 河南科技大学机电工程学院
  3. 河南中烟工业有限责任公司洛阳卷烟厂
- 作者简介：
- 基金信息：
- DOI：10.16578/j.issn.1004.2539.2015.03.001
  CLC：
扫描看全文
[1]邓静,邓效忠,谢君军,蒋闯,耿龙龙.数控铣齿机结构创新及其加工准双曲面齿轮的试验研究[J].机械传动,2015,39(03):1-4.

Deng Jing, Deng Xiaozhong, Xie Junjun, et al. Study on the Structural Innovation and Gear Cutting Experiment of Hypoid Gear for a CNC Milling Machine Tool. [J]. 39(3):1-4(2015)
[1]邓静,邓效忠,谢君军,蒋闯,耿龙龙.数控铣齿机结构创新及其加工准双曲面齿轮的试验研究[J].机械传动,2015,39(03):1-4. DOI： 10.16578/j.issn.1004.2539.2015.03.001.

Deng Jing, Deng Xiaozhong, Xie Junjun, et al. Study on the Structural Innovation and Gear Cutting Experiment of Hypoid Gear for a CNC Milling Machine Tool. [J]. 39(3):1-4(2015) DOI： 10.16578/j.issn.1004.2539.2015.03.001.

摘要

介绍了YK2260X数控铣齿机的结构创新要点。推导了数控弧齿铣齿机变性法加工准双曲面齿轮各轴运动的表达式,确定了参考点对刀位置、起始加工位置、终止加工位置的坐标,介绍了数控弧齿铣齿机编程的流程。在YK2260X数控弧齿铣齿机上对一种汽车驱动桥的准双曲面齿轮进行了切齿试验,结果表明,四轴联动数控弧齿铣齿机内置变性法切齿加工软件,可以用HFM法加工准双曲面齿轮小轮,所加工的齿轮接触区良好,能够满足设计要求。

Abstract

The key points of structural innovation of a CNC milling machine tool YK2260 Xis introduced.The expressions of the movement of each axis by using modified-roll method for machining hypoid gear are deduced,the coordinates of the setting position,the initial as well as the terminal positions for machining are determined,and its programming procedures is introduced.A cutting experiment is performed on the YK2260 Xfor a kind of hypoid gear used in drive axle for automobile,the result indicates that with the software of modified-roll method installed,applying HFM method,the hypoid pinion would be machined by the 4-axis CNC milling machine tool.The contact area of the machining gear is favorable and satisfies the requirements of design.

关键词

准双曲面齿轮数控铣齿机结构创新变性法驱动软件

Keywords

Hypoid gearCNC milling machine toolStructural innovationModified-roll methodDriver software

references

Views

152

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Contact Simulation and Dynamic Performance Test of Ease-off Modified High Reduction Hypoid Gears

Tooth Contact Analysis and Adjustment Calculation of Real Tooth Surfaces of Hypoid Gears

Research on Transmission Error of Hypoid Gear based on Real Tooth Surface

Optimization of Churning Resistance of Hypoid Gear for Automobile Rear Axle

Forming Defects Analysis and Process Setting of Hot Rolling Technology of Hypoid Gear

Related Author

No data

Related Institution

School of Mechanical & Electronic Engineering, Henan University of Science & Technology

School of Numerical Control Technology, Xinxiang Vocational and Technical College

Liuzhou Wuling Automobile Industry Co.，Ltd.

School of Mechanical and Electrical Engineering， Wuhan University of Technology

School of Mechanical and Electronic Engineering， Wuhan University of Technology

⁰